What Type of Grease for Lubricating Trailer Jack

Question

Question:

The weld on trailer jack, what kind and/or type of lubrication do you use, i.e.,gear lube, heavy grease? Thanks

asked by: Richard

0

Expert Reply:

I am not totally sure which jack you are referencing but most jacks are designed to be lubricated with white lithium grease like part # L11354.

expert reply by: Jameson C

0

Answer 1

Hello Todd. The Base of the Fulton Single Speed Trailer Winch #F59CR is 5-3/8" long and 3-9/16" wide. The total height of the unit is 6-1/8" tall. I threw together a few diagrams to help illustrate. Hope this helps!

view full answer...

Answer 2

3/8 inch diameter Grade 5 or higher hardware would be what you'd need to mount the Fulton XLT winch part #F142425 that you referenced. A total of 3 bolts would be all you'd need.

view full answer...

Answer 3

Good news! I was able to get a exploded diagram as well as a set of instructions on how to replace the rod and gears #TJD-12000-RODNUT in the #12000 Series Ram Jacks made after 2012. I have attached them to this page for your convenience. Basically,…

view full answer...

Answer 4

As long as the THNN wire is copper and the proper gauge for what you are wiring on your trailer you can use it. I have attached a helpful article that explains wiring a trailer and the minimum required wire gauges. We recommend at least 10 gauge wire…

view full answer...

Answer 5

For a typical trailer wiring you will have a brown and green wire for the right-hand side of the trailer and brown and yellow wire for the left side. If this is a new wiring installation and you are installing wiring like part #A35W42B, the brown…

view full answer...

Answer 6

Most trailer wiring that runs to incandescent trailer lights is 16 gauge which would be a little less than what we would like, However for LED lighting 16 or 18 gauge is fine. To make your project easier I would use the Optronics #A35W42B wiring…

view full answer...

Answer 7

The Curt 45951 Rebellion Shock absorbing ball mount which we offer as part #C83WR would certainly reduce much of the shock and vibration that's experienced when towing a trailer which would absolutely make towing a more pleasant experience. Much…

view full answer...

Answer 8

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 9

You certainly can install two pairs of the Ark Drop Down Corner RV Stabilizer Jacks #ARK77FR on your trailer. In that case we recommend adding one jack to each corner of the trailer frame. Keep in mind that these are designed to stabilize, not lift…

view full answer...

Answer 10

Good question, and we have asked the manufacturer, Ark, this very same question, and they have said there is not any weight rating for the Ark Drop Down Corner RV Stabilizer Jacks - 33" Long Corner Steadies #ARK77FR. They say the reason they…

view full answer...

Answer 11

Yes, your trailer with corner jacks can still absolutely use the Ark stabilizers: - Ark Drop Down Corner RV Stabilizer Jack Kit - 24" Long Corner Steadies #ARK34FR These will weld to the bottom of your trailer's frame, you just need to make…

view full answer...

Answer 12

We don't offer a combination leveler/stabilizer jack, but if you're wanting something in a stabilizer jack that is very sturdy, you can't go wrong with the ARK Drop Down Corner stabilizer jacks. They're available in a powder coat or a…

view full answer...

What Type of Grease for Lubricating Trailer Jack

Product Page this Question was Asked From

Continue Researching