Regulator for Dyna-Glo Wall Heater Model # IR30PMDG-1

Question

Question:

Dyna-Glo wall heater Model # IR30PMDG-1 - what regulator, gauge or parts do I need?

asked by: Cathy J

0

Expert Reply:

I looked up your Dyna-Glo wall heater Model # IR30PMDG-1 and it's propane requirements are a 100 lb propane tank using low pressure propane. It's max BTU rating is 30k too. Based on that the # 108220 that you referenced would work great.

expert reply by: Jameson C

0

Answer 1

For your 30,000 BTU wall mounted heater you will need to use a dual-stage propane regulator. The correct regulator will be the MB Sturgis Vertical 2-Stage Propane Regulator - 11" Water Column Outlet #108220. You will need a vertical regulator if…

view full answer...

Answer 2

According to the user manual for Dyna-Glo wall heaters, they require a propane gas line pressure of 11in WC (water column). You will need a 2-stage regulator to reach this pressure level like part #37207-30375. This regulator comes with the POL…

view full answer...

Answer 3

Thanks for the picture of the LP requirements of your dryer. It uses a standard 10 water column propane pressure rating so the regulator part #108220 that you referenced is a good start since that is what this is designed for as well. You'll need…

view full answer...

Answer 4

I went ahead and checked to see what we have an unfortunately it does not appear that we have a hose that will connect your regulator with a 3/4" FPOL inlet to your 100-lb propane tank, however I do have another solution. I know it is not ideal,…

view full answer...

Answer 5

Dyna-Glo Blue Flame Wall Heaters require an external propane regulator and a have a 3/8" NPT fitting so you'd need to get a regulator and compatible pipe/hose fitting to connect to your propane source. Regulators have vents built into them…

view full answer...

Answer 6

Yes, you should go with a dual stage like the MB Sturgis 2-Stage Propane Regulator part #108220 for vertical or part #108221 for horizontal because it can be adjusted to a 12" water column outlet. In order to do this you will need to remove the…

view full answer...

Answer 7

For your 30,000 BTU LP garage heater you will want to use a dual-stage propane regulator. If you need a vertical regulator the MB Sturgis #108220 will work great or for a horizontal regulator you can use part #108221. These dual-stage regulators will…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

Answer 12

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Regulator for Dyna-Glo Wall Heater Model # IR30PMDG-1

Product Page this Question was Asked From

Continue Researching