Can Hand Winch Be Added to Trailer Tongue of Roadmaster Tow Dolly?

Question

Question:

i have a tow dolly road master 2000-1 and would like to mount a hand winch on the tongue would it hurt too drill holes through the tongue 2 to 3 holes in a line about 3 inches apart

asked by: Albert Z

0

Expert Reply:

The Roadmaster Tow Dolly with Electric Brakes # RM-2050-1 will allow you to mount a hand winch. My recommendation is the Dutton-Lainson Hand Winch - Worm Gear - Hex Drive - 2,000 lbs # DL11004 which will allow you to remove the handle.

expert reply by: Jason S

0

Answer 1

Typically, we want a winch that will be used to load a car trailer to have a line pull capacity at least 50% greater than its. gross vehicle weight With that in mind, my recommendation is the Bulldog Winch Trailer Winch - Synthetic Rope - Hawse…

view full answer...

Answer 2

For mounting a winch to a trailer like the Superwinch #SW1455201 one solution is to weld a hitch tube to the trailer like with the part #E-9 so that you could use a winch mounting plate like the #BDW20011 and have a way to easily remove and reinstall…

view full answer...

Answer 3

Curt front mount trailer hitch #31313 fits all models of the 2007 Toyota Tacoma. There should not be any interference with any of the truck components since the hitch sits out in front of the ends of the frame and in front of the bumper beam as shown…

view full answer...

Answer 4

For the Curt winch mount, #C31010, or any of the similar mounts, you will need to compare the mounting pattern on the mount to what your winch requires. I have included 2 pictures. One shows the mount pattern of the Curt mount.

view full answer...

Answer 5

The Superwinch S7500 Trailer Winch #SW1475201 is designed to have more of a "universal" style for mounting and may require some adaption for installation because it does not have a typical mounting pattern. The Superwinch S7500 Trailer…

view full answer...

Answer 6

I do have an option for you but there isn't any receiver mount options for the Superwinch Winch 2 Go Portable part #SW1140232 since it's designed to be portable and it's a little underrated for full-size trucks. Instead, I recommend the…

view full answer...

Answer 7

I have a selection of front mount hitch mounting plates to choose from. I am including a link to a product page that will list the choices of mounting plates. Our most popular mounting plates for front mount hitch is the CURT Trailer Hitch Electric…

view full answer...

Answer 8

I can understand why this might be confusing, when it comes to the different ratings. Rolling capacity is essentially just the capacity of the winch to pull a load that is moving up an incline; technically the capacity that is listed is the maximum…

view full answer...

Answer 9

Yes, the Warn M8000 Winch uses a 10" x 4-1/2" mounting pattern which the Curt Trailer Hitch Electric Winch Mount Plate part #C31010 will accept so they can be used together just fine. The 10" x 4-1/2" mounting pattern is an…

view full answer...

Answer 10

I spoke with my contact at Bulldog winch and he stated that you can remove that tensioner piece you mentioned on winch #BDW15020 which should make it easier to freespool! So that is great news.

view full answer...

Answer 11

The Bulldog Winch part #BDW15020 would be a great option for your setup. This is a 4,400 lb 12 volt winch which uses a synthetic rope instead of a steel cable. It powers in and out and has a built in brake as well. The winch also moves at 19 feet per…

view full answer...

Answer 12

I went out to the warehouse and pulled a CURT Trailer Hitch Electric Winch Mount Plate, #C31010, to measure it. From the back of the mounting plate to the center of the nearest hitch pin hole, it is 4-1/4 inches. -The distance to the center hole is…

view full answer...

Can Hand Winch Be Added to Trailer Tongue of Roadmaster Tow Dolly?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching