Torque for 7,000 lb, 12 Inch x 2 Inch Dexter Electric Brakes

Question

Question:

tourque value for the 5 plate mounting bolts??

asked by: John T

0

Expert Reply:

The Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 7,000 lbs # 23-181 and Left Hand # 23-180 should should be torqued to 30-50 foot/lbs.

expert reply by: Kyle S

0

Answer 1

The difference between the Dexter Electric Trailer Brake Kit - 12" - Left and Right Hand Assemblies - 7,000 lbs #23-180-181 and the #23-105-106 you mentioned are the strength of the brake magnets. The #23-180-181 was designed for 7000lb axles…

view full answer...

Answer 2

Hey Kenneth, to get max stability it is best to use three of the MORryde X Factor crossmembers on a tandem axle trailer. For that you'd need the part #MR33WR since you have stock suspension hangers. You wouldn't need longer hardware than what…

view full answer...

Answer 3

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 4

The first thing you'll want to check is the weight rating of your trailer. This will be stated on your paperwork or on the trailer near the front somewhere. Whatever the GVWR states will be the max weight you can load your trailer. You can…

view full answer...

Answer 5

I have another option for you, but we do not have any 13" trailer wheels with offset to push the tire further from the frame, and do not recommend using any spacers as they can cause additional stress on the hubs which can wear out bearings and…

view full answer...

Answer 6

According to Dexter, the nut should be torqued to between 45-70 foot lbs. If you don't have a torque wrench close at hand, Tighten the bolts until the lock washer flattens, which will put you really close to the correct torque. We offer 4 nuts…

view full answer...

Answer 7

44 lbs. The Kenda Karrier ST205/75R15 Radial Trailer Tire with 15" Black Mod Wheel item #AM32238B weighs a combined 44 lbs.

view full answer...

Answer 8

There is a wet bolt kit made specifically for a tandem axle trailer with Road Armor equalizers, and includes the shackles, wet bolts, and hardware needed. What you need is the following part: - Lippert AP Kit - Tandem Axle Road Armor Wet Bolts and…

view full answer...

Answer 9

The reason that 10 Gauge #10-1-1 or 12 Gauge #12-1-1 wire is recommended for 10" brake assemblies, like part #AKEBRK-35-SA, is because they pull more power than the lights on your trailer. I believe the green wire you are referring to carries…

view full answer...

Answer 10

Karrier and Loadstar are two different brand names used by Kenda. There's no difference in quality or function between the two brand names. For a ST175/80-13 Radial trailer tire in load range D, I'd recommend part #AM10210 if you're…

view full answer...

Answer 11

We can definitely get your trailer a more sleek look, although there is not a black center cap for the Kenda Karrier ST205/75R15 Radial Trailer Tire with 15" Black Mod Wheel - 5 on 4-1/2 - LR C #AM32238B you asked about, because this wheel has a…

view full answer...

Answer 12

The grease cap you need is part #21-42-1. The rubber plug that you would then need is the part #RG04-010. We are going to need to know the width of your current grease cap on the other trailer to pick out a Bearing Buddy. Or you can measure the inner…

view full answer...

Torque for 7,000 lb, 12 Inch x 2 Inch Dexter Electric Brakes

Product Page this Question was Asked From

Continue Researching