Should Timbren Spacers or Off-Road Bumpstops be Used for a 2015 Toyota Tundra with 2-1/4" Lift

Question

Question:

What is the length of the active offroad bump stop? Would it firm or a little give?

asked by: Jim

1

Helpful Expert Reply:

The Timbren Spacers, like the 1" # A25723-90AH00 or 1/2" # TA25722-90P00, are designed to be used with a Timbren suspension enhancement system so you will not want to use them with your factory bumpstops.

I spoke with my contact at Timbren about using the Timbren Active Off-Road Bumpstops # TABSTOF with the 2-1/4" lift on your 2015 Toyota Tundra and my contact said that no spacers will be needed when installing these.

The Off-Road Bumpstops are rated for 1,800 lbs, but keep in mind that any suspension enhancement system will not increase your weight capacity. It is designed to enhance a normal functioning suspension system.

expert reply by: Jon G

1

Jim

11/27/2017

What is the length of the active offroad bump stop? Would it firm or a little give?

Reply

Jon G.

11/27/2017

I spoke with my contact at Timbren who said that the Timbren Active Off-Road Bumpstops # TABSTOF have a height of 1-7/8" and have a 2-5/16" diameter. These bumpstops are firm but they do have a little bit of give and are an upgrade to your current bumpstops.

Reply

Answer 1

The Timbren Active Off-Road Bumpstops #TABSOSR referenced in your question feature an assembled height of 4-5/8 inches. I have attached a short video review on this kit along with the written installation instructions that you can check out as well.

view full answer...

Answer 2

The Timbren Active Off-Road Bumpstops part #TABSOSR which are a fit for a 2007 Toyota Tacoma are designed so that there is more space between the spring and frame to allow the suspension to articulate freely when off-road. If you're looking for a…

view full answer...

Answer 3

To add a 1" spacer #A25723-90AH00 to the Timbren Active Off-Road Bumpstops #TABSOSR you were looking at for your 2014 Toyota Tundra you will need to purchase two grade 5 or 8 3/8" x 2-1/2" F/T UNC bolts from your local hardware store.…

view full answer...

Answer 4

There are six different Timbren kits for suspension enhancement that all fit your 2018 Toyota Tacoma. Four are for the rear and two are for the front. Of the front two, part #TTOFTUN4 is designed for adding support when you put a snow plow on the…

view full answer...

Answer 5

The Timbren Active Off-Road Bumpstops - Rear Suspension - 3,600 lbs #TABSTRFK have bump stops and mounts that are 5-1/2 inches tall overall and u-bolts that are 8-1/4 inches long and 3-3/4 inches on center. I've attached a photo to assist. These…

view full answer...

Answer 6

There is an interesting amount of Timbren kits that fit your 2022 Toyota Tacoma long bed. The part #TABSTRFK is a standard duty kit that comes with a U-bolt flip kit helps with ground clearance. #T72FR is a severe service kit for 3 leaf springs which…

view full answer...

Answer 7

For your 2013 Toyota Tundra that is towing a 6,500 lb travel trailer I'd go with the Timbren kit part #TABSOSR to help support the rear of it and reduce sag as this will give you up to an additional 3,600 lbs of support if needed. Other kits…

view full answer...

Answer 8

Suspension enhancement systems like Timbren springs are perfect for the scenaro you're describing. These solutions supplement your factory suspension but don't necessarily increase your capacity. Timbrens are hollow rubber springs that sit…

view full answer...

Answer 9

For your 2021 Chevy Colorado 4x4 we have the Timbren rear suspension kit part #TABSOSR as a confirmed fit that would do an excellent job reducing the sag you are experiencing. SumoSprings does not have a kit for your truck at this time but the…

view full answer...

Answer 10

For your 2018 Chevy Colorado ZR2 Diesel I recommend RoadActive Suspension #RAS4617. This system will provide extra support when towing and/or carrying loads in the truck bed as well as help with overall stability all without affecting the unloaded…

view full answer...

Answer 11

The Timbren Springs #T28MR has an overall height of 5-11/16". With your 2021 GMC AT4 having the factory lift you will want to measure the distance from inside the cup on your current jounce bumper to the pad on the axle. We do have a 1"…

view full answer...

Answer 12

Apparently this was a known issue because Timbren put a couple of notes in the instructions regarding the use of penetrating oil to remove the fasteners for the OEM hardware and, if the factory nut is damaged, to use the supplied fastener. This…

view full answer...

Should Timbren Spacers or Off-Road Bumpstops be Used for a 2015 Toyota Tundra with 2-1/4" Lift

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching