Where Does a Brake Controller Install on a 2001 Dodge Ram 1500
Question:
where is the factory plug for electric brakes location under dash on my 2001 dodge ram. i believe i found it but its plugged into the back of the e-brake. is this the plug im looking for an if so do i just unplug it from the e-brake?
asked by: Brad
Expert Reply:
The correct adapter to install the Brake Controller part # 39510 you referenced in your 2001 Dodge Ram 1500 is the part # 3020-P.
This adapter plugs into the 4-pin connector on your vehicle's built-in brake control wiring harness. The harness is located underneath the dash, to the left of the steering column, taped to another harness near the emergency brake pedal.
I attached a picture of the blue connector plus a link to an install video that will walk you through the process.
Products Referenced in This Question
Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Dodge
- Accessories and Parts
- Trailer Brake Controller
- Wiring Adapter
- Plugs into Brake Controller
- Vehicle Specific
- Tekonsha
more information >
Product Page this Question was Asked From
Tekonsha Voyager Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Splice-In
- Under-Dash Box
- Under-Dash
- Up to 4 Axles
- Indicator Lights
- Single Trailer Only
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Brake Controller
- Video: How to Choose a Trailer Brake Controller
- Shop: Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Dodge
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Search Results: brake controller
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Search Results: tekonsha 90160
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Kodiak Disc Brake Kit - 12" Rotor - 6 on 5-1/2 - Stainless Steel - 5,200 lbs to 6,000 lbs
- Q&A: Should I Have Constant 12 Volt Power On Brake Output Pin On 7-Way Connector
- Search Results: prodigy 2
- Shop: Curt Spectrum Brake Controller w/ Plug-In Harness - Dash Mounted Knob - Up to 4 Axles - Proportional
- Shop: Kodiak Trailer Hub for 5,200-lb to 6,000-lb Axles - 6 on 5-1/2 - Stainless Steel
- Shop: Wiring Kit for 2, 4, 6, and 8 Brake Electric Trailer Brake Controllers
- Search Results: pace american
- Search Results: pace trailer parts
- Search Results: 51332
- Shop: Trailer Wiring
- Search Results: tekonsha trailer brake controller
- Q&A: Replacement 6-on-5-1/2 Idler Hub Kit to Replace Hub 82655
- Video: All You Need to Know About the Kodiak Disc Brakes
- Video: Complete Breakdown of the Kodiak Disc Brake Kit
- Video: Detailed Breakdown of the Kodiak Trailer Hub for 5,200-lb to 6,000-lb Axles
- Video: Feature Breakdown: Universal Installation Kit for Trailer Brake Controller
- Q&A: How To Choose the Correct Axle Hub Face Length When Building a Trailer
- Q&A: Why Are There Both Round and Square Trailer Axles Used on RVs
- Article: Electric Brake Controller Installation on Dodge Ram Trucks to 2012
- Q&A: Recommended Plug and Play Adapter for a Curt Brake Controller on a 2019 Ram 1500
- Article: Troubleshooting Brake Controller Installations
on Trailer Brake Controller
