Fuse Location for Electric Brake Controller on 2003 Ford F-350

Question

Question:

Where is the fuse location for tekonsha voyager brake system on a ford f350 2003 model

asked by: Karen B

0

Expert Reply:

According to the owner's manual for the 2003 Ford F-350, the fuse for the brake controller is location 22 in the power distribution box which is in the engine compartment. Take a look at the snap shot that I have included for you.

expert reply by: Leah S

0

click to enlarge

A H.

3/2/2024

I cant find this in my truck. its a 2003 ford f350 superduty,

Reply

Jerred H.

3/2/2024

@AH I looked at your F-350's owners manual. You will want to go to the interior fuse panel and check the 30 amp fuse in the 101 location. This is the trailer tow electric brake fuse.

Reply

Answer 1

It sounds like you have checked your 12V circuit with a circuit tester like #PTW2993 and you do not have power at the plug on the 2003 Ford F-250 with towing package. Most likely the trailer tow battery charge fuse is the culprit. From my research…

view full answer...

Answer 2

If you check out the attached instructions for the Curt TriFlex Trailer Brake Controller #C24VV you can see that the OL code you are getting means that there is an "Overloaded output circuit, trailer brake system fault". Whichever…

view full answer...

Answer 3

The blue wire on a brake controller is output to the trailer brakes. If that wire is not connected the trailer brakes will not be getting any power. If there is a break in that wire somewhere between the controller and the trailer connector then that…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Hey Scott, yes the hardware that comes with the Replacement Track Adapter Installation Hardware for Yakima OverHaul HD #Y69KR would fit into the tonneau cover tracks that you have on your 2020 Ford F-350 with the Embark tonneau. This kit will not…

view full answer...

Answer 6

It sounds like you are going to have to go with the Yakima LockNLoad Platform Roof Tray #Y05048 along with 3 sets of the Crossbar Clamps #Y05039 to fit on your Yakima OverHaul HD Adjustable Truck Bed Ladder Rack #Y01151-58 on your 2023 Ford F-250…

view full answer...

Answer 7

Because the Retrax PRO MX Tonneau Cover #RT80467 for the 2019 Chevy Silverado 2500 covers the bed rails, you would not be able to use a ladder rack like the Thule TracRac #TH27000XT since that rack requires the use of the bed rails. The only tonneau…

view full answer...

Answer 8

I don't see any issue with installing an axle flip kit on a drop axle aside from the shape of the axle as we only offer kits for rounds axle, the Dexter Trailer Springs Over-Under Conversion Kit part #K71-384-00 or part #K71-385-00.

view full answer...

Answer 9

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 10

Hey Patrick, Yes, the Base Rails for Thule TracRac SR Sliding Truck Bed Ladder Racks #TH33JV would be the correct base rails for your 2025 GMC Sierra 2500 short bed.

view full answer...

Answer 11

Hello Ken. I am not sure exactly how long your current U-bolts are, but you will probably be able to re use them. It just depends on how long they are and how much thread is left. Assuming your 4 leaf spring has 3/8" thick leaves it would be…

view full answer...

Fuse Location for Electric Brake Controller on 2003 Ford F-350

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching