Replacement Install Hardware for DeeZee Tailgate Assist # DZ43301

Question

Question:

I need a new nut . Will you sell me the product . I have a 1500 Ram Truck 2011 .I striped the nut device piece . All I need is the expansation device . This for your a tailgate assist product.Please let me know ASAP Thank you

asked by: Kenneth K

1

Helpful Expert Reply:

We offer a replacement hardware kit, part # BKT43301 that includes all the hardware, minus the gas shock. The nutsert that installs into the side of the tailgate that provides an attachment point for the shock isn't sold as a separate item.

expert reply by: Mike L

1

click to enlarge

Answer 1

For the DeeZee tailgate assist we have the replacement hardware kit part #BKT43301 that comes with the new bolt you are looking for plus a few other things that you could keep as replacement parts.

view full answer...

Answer 2

DeeZee Tailgate Assist Custom Tailgate-Lowering System #DZ43301 does have what they call a nut zerk fitting like what you show in your picture. If you just need to replace that part use #BKT43301. You have to be very careful not to over tighten this…

view full answer...

Answer 3

The MagnaFlow Cat-Back Exhaust System #MF15333 is confirmed to fit a 2018 Ram 2500 Crew Cab with an 8 Foot Bed or Mega Cab with a 6-1/2 Foot Bed and a 6.4L V8 HEMI. The installation details have been linked for you to reference.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Hello Lou, thanks for reaching out. The hitch pin you are looking for is the etrailer D-Shape Anti-Rattle Locking Hitch Pin for Benton Hitch Accessories #e43JR. This will work with the Benton #B54VR bike rack you mentioned, as well as the #B54FR,…

view full answer...

Answer 10

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 11

Since yo have a ducted Coleman setup currently the best option is the Furrion Chill unit part #FR42PV which was designed for your exact setup so it would be an easy install using same controls. This is also the quietest and coldest blowing unit we…

view full answer...

Answer 12

Hello Dave, Great question. Unfortunately, you cannot use a RockerBall with a Reese Goose Box because the Goose Box requires a fixed gooseneck ball, while the RockerBall has a built-in pivot mechanism that could cause instability. The Goose Box…

view full answer...

Replacement Install Hardware for DeeZee Tailgate Assist # DZ43301

Product Page this Question was Asked From

Continue Researching