T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector

See what our Experts say about this Tekonsha Custom Fit Vehicle Wiring

• Recommended Trailer Hitch Receiver For 1990 Chevy C2500 Short Bed With Ranch Hand Bumper
  For your 1990 Chevy C2500 with ranch hand bumper, I recommend the Draw-Tite Max-E-Loader Trailer Hitch Receiver - Custom Fit - Class III - 2" # 41504. This is an easy bolt-on installation that has long side brakets to help distribute the weight over a large portion of the frame for increased towing ability. It is a square tube design with black powder coat over an e-coat base for superior rust protection. If you don't already have trailer wiring, I recommend the Tekonsha T-One Vehicle...
  view full answer...
• Installing Tekonsha P-3 Trailer Brake Controller # 90195 On 1994 GMC Sierra
  The wire from the Tekonsha P-3 Trailer Brake Controller, part # 90195, that connects to the brake light switch is Red. To determine which wire you will need to splice into on your 1994 GMC Sierra, you will need to use a circuit tester, part # PTW2993. You will need to connect the red wire from the brake controller to the wire that only has signal when the brakes are applied. If you have trouble finding the stoplight switch wire, you can splice into the Center High-Mount Stoplight wire. In...
  view full answer...
• How to Install 4-Way Trailer Connector on 1999 Chevrolet Silverado 1500 with Factory Tow Package
  The Tow Ready T-One Wiring Harness, part # 118315, is for the 1988 to 2000 Chevrolet C/K Series trucks. It is not for the 1999 Chevrolet Silverado 1500. The 1999 Chevrolet Silverado 1500 would use either the Tow Ready Wiring Harness, part # 118384, which is used if you have a harness that is located under the vehicle, behind the bumper, on the driver’s side of the vehicle. The wiring harness # 118384, is meant to plug in line with the factory wiring and provide a 4-Way flat connection....
  view full answer...
• How to Wire a 7-Way Trailer Connector on a 1994 Chevrolet C/K Pickup
  To wire a 7-Way trailer connector at the rear of your 1994 Chevy pickup, you will need to start with a working 4-way connector, item # 118315, if your truck is not already equipped with one. You would then use the 4 Pole to 7 Pole and 4 Pole Adapter, item # 37185, and plug in the 4-Way on the truck to provide the stop turn and tail light functions in the adapter. If you do not need the brake control feed wire, 12 volt power wire or backup wire for your trailer you can tie one or all of...
  view full answer...
• How To Wire Brake Controller in 2000 Chevy K2500
  The 2000 Chevy C/K Series does not have a plug in the relay box or under the dash to plug a brake controller adapter into. To wire in a brake controller like part # 90195 it would be a hardwired application. To accomplish wiring in the brake controller, you will need a 4-Way to 7-way kit part # ETBC7. Some of the C/K series trucks have OEM wiring extended to the back of the truck already but not all trucks are equipped with the partial wiring. To find the partial wiring (if you have it)...
  view full answer...
• Will an Old Reese Multi-fit Trailer Hitch Fit a 2000 GMC 1/2 Ton Pickup Truck
  The old multi-fit trailer hitch, 37042, was made obsolete in August of 2009. But I managed to find a list of the vehicles that it fits. It does NOT fit your 2000 GMC 1/2 ton pickup truck. The most popular hitch for a 2000 GMC C/K Series 1500 is # C14081. I also recommend ball mount kit # EBMK2416. And if you need trailer wiring use # 118315. If your truck is a Sierra (2000 was a split year) then the most popular hitch for the 1500 is # 13322. I also recommend ball mount kit # EBMK4. And...
  view full answer...
• 7-Way Connector and Brake Controller Recommendation for a 1998 Chevy Cheyenne K1500 4x4
  If you install a Curt Wiring Adapter # C57674 onto your 1998 Chevy Cheyenne, you could use either the 7-Way or the 4-way adapter to hook up to your trailer. If you do not have one, you will first need a 4-Way connector at the rear of your truck. I would recommend you get a Tow Ready T-One Vehicle Wiring Harness, part # 118315. I attached installation instructions for this product below. If you used the 7-Way, it would function just like a 4-Way in that you would not have trailer brakes....
  view full answer...
• Recommended Trailer Hitch Receiver For 1998 Chevy K3500
  For a 1998 Chevrolet K Series 3500 Pickup, I recommend the Draw-Tite Ultra Frame Trailer Hitch Receiver Class IV - 2" # 41901. This is an extremely sturdy hitch that is easy to install. It will fit a standard or step bumper. For a roll-pan bumper, use # 41522. For your wiring, I recommend the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118315 to get a 4 way connection. Then you will want to add the # ETBC7 to get your 7 way connection along with the circuit breakers,...
  view full answer...
• Curt Brake Controller Installation on 1998 Chevrolet C/K Series Pickup with Long Bed
  To help installation of the Curt TriFlex Trailer Brake Controller # C24VV go smoothly, you will want a 4-way connector, the universal wiring adapter for Curt brake controllers # C51515, and the universal installation kit # ETBC7. If you do not already have a 4-way connector on your pickup, you will want to begin by installing one. I recommend the Tow Ready T-One Vehicle Wiring Harness # 118315. This wiring harness plugs directly in your vehicle's pre-existing wiring with no cutting or...
  view full answer...
• Fit of Tow Ready T-One Connector # 118315 on 1989 Chevy K1500 w/ Custom Bumper
  The Tow Ready # 118315 is designed to fit a 1989 Chevy K1500 with a stock bumper. The lamps on your bumper should plug into the factory wiring harness on the driver's side frame rail. The # 118315 will plug inline at that connection as long as it hasn't been altered. If your connector looks like what's shown in the photo and video I've linked for you, the # 118315 should fit without cutting or splicing.
  view full answer...
• Trailer Hitch for 1998 Chevy C/K 1500 to Tow a 7,000 Pound Trailer
  Yes, Draw-Tite trailer hitch # 37130 will have the capacity for a trailer weighing 7,000 pounds. This hitch maxes out at 7,000 pounds without weight distribution so you might consider a higher capacity hitch. Curt trailer hitch # C14081 is a great option. It is only a few dollars more than the Class III hitch and it has a 10,000 pound gross trailer weight capacity. Be sure to consult the truck owners manual to make sure it too can tow the 7,000 pound trailer. Installation is fairly straight...
  view full answer...
• Recommended Trailer Hitch Receiver For 1991 Chevrolet C/K Pickup W/ Roll Pan
  As long as your 1991 Chevrolet C/K Series Pickup is a 1500 I recommend the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # 13942 which is designed to work with trucks that have a roll pan installed, but you will need to cut a hole in the roll pan behind the license plate for the hitch to work. At this time there is not a trailer hitch receiver for the 2500/3500 trucks with a roll pan. The # 13942 has a 500lb tongue weight rating and 5000lb trailer weight rating making it a...
  view full answer...
  
• Installing Brake Controller On 1998 GMC Sierra
  To install a brake controller in your 1998 GMC C/K series 1500, there are a couple of items you will need in addition to the brake controller. If the truck does not have a 4-Way trailer connector, you will need to add one like part # 118315. The harness plugs in so no cutting or splicing is required. After making that connection, you will just need to attach the white ground wire to a clean, bare metal surface. Then you will need the 7 and 4 Way Installation Kit, part # ETBC7. First,...
  view full answer...
  
• Does a Brake Controller Have to be Hardwired in 1991 Chevy C/K Truck
  Yes, a brake controller will need to be hardwired into a 1991 Chevy C/K Series truck, though the installation is not something overly difficult. To install the brake controller I recommend for your truck, the Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional # 90885 you will need the Brake Control Plug-In Harness # 20127, which plugs into the Prodigy and has four wires, a black power wire, white ground wire, blue brake wire and red stop light switch wire. If...
  view full answer...
  
• Adding a 7-Way in the Bed of a 1999 GMC 2500
  To add a 7-Way trailer connector to the bed of your 1999 GMC truck you have some options. First, if the truck came with a factory 7-Way then you can just use # C56080 which will plug into the 7-Way at the rear of the truck. If your truck does not have a 7-Way then you would first need to install one. To do this you can use # ETBC7. For this to install you would need to have a 4-Way flat trailer connector at the back of the truck. If you do not then you can install one, # 118315, and then...
  view full answer...
• Parts Needed to Add 7 Way and Brake Controller to 1998 Chevrolet Truck
  To add a brake controller to your truck and swap out the connector with a 7 way you'll need a few parts. You'll need a working 4 pole flat trailer connector (which you said is currently on the truck), the Universal Installation Kit for Trailer Brake Controller # ETBC7 and a brake controller. The ETBC7 kit comes with all the connectors, breakers, and wires to get a brake controller installed and a 7 way at the back of your truck. The 4 pole wiring will plug into the ETBC7 and then wires...
  view full answer...
  
• Does the Curt 2 inch Bumper Hitch # E-3S work on a 1995 Silverado Short-bed 1500
  The Curt 2 inch Bumper Mounted Hitch, 5,000 lbs GTW, item # E-3S, will work for towing up to the 5,000 pound gross trailer weight rating and 500 pound tongue weight rating of the hitch or the capacity of your truck step bumper, whichever is lowest. You should check the capacities of your step bumper and the gross trailer weight and tongue weight of the trailer you will be pulling to be sure it is within the capacity of the hitch and bumper. I have provided installation instructions for...
  view full answer...
• Trailer Hitch Recommendation for a 1996 Chevy C/K Series 1500 Pickup Truck with Dual Exhaust
  The Curt Trailer Hitch, # 13942, is designed to fit if the truck has a roll pan. There is no restriction if the truck has dual exhaust. I have included a link to the installation instructions for this hitch for reference. This is the only hitch specifically designed for use if the truck has a roll pan. I have included a link to all of the trailer hitch options for a 1996 Chevy C/K 1500. Just select your specific truck style from the pull down menu under where it reads Select Vehicle Style...
  view full answer...
• Wiring Harnesses Needed to Install a Brake Controller on a 1995 GMC C3500
  Chances are the 1995 GMC C3500 did not come with a factory tow package, so you will have to hardwire the vehicle if you want to use any brake controller. It is not as difficult as it sounds. You will need a few things first. You will need the Brake Controller 7 and 4 Way Installation Kit, # ETBC7. I have included a couple of videos showing this kit being installed. You will also need the Tow Ready Custom Fit Vehicle Wiring, # 118315, if you do not already have a 4-flat connector. I have...
  view full answer...
• Parts Needed to Install a Brake Controller on a 1997 Chevy C/K Series Pickup Truck
  There is no brake controller port for a 1997 Chevy or GMC C/K series pickup truck. It is a hardwire installation only. This means the brake controller has to be spliced in. The red wire in this case would attach to the cold side of the brake switch. The brake switch is located above the brake pedal. Use a circuit tester such as # PTW2993 to test the brake switch wires. You need the one that only has power when you step on the brake pedal. If it has power at any other time, such as with...
  view full answer...
• How to Install Prodigy P3 Brake Controller in 1994 GMC C/K
  Yes, you can install the Prodigy P3 part # 90195 in your 1994 GMC Sierra 2500 and it will work great. You will need to start with a 4-way (if you do not have one). For that you would want the # 118315. From there you would need to convert the 4-way to a 7-way so that you can install the brake controller. For that you will want the Brake Controller Install Kit and 7-Way Adapter part # ETBC7. I attached installation instructions and an install video for this product as well. The video...
  view full answer...
• Recommended 7-Way Harness for 1995 GMC Sierra
  We do have what you need to install a fully functional 7-Way connector on your 1995 GMC Sierra, however there is not a plug and play 7-Way option similar to the 4-Way Harness # 118315 available for your truck. If you do not yet have a connector installed on the Sierra, you will actually want to start with the mentioned Tekonsha T-One Harness # 118315. This will plug into a factory port under the truck on the driver side. Once installed, I recommend using the Universal Wiring Kit # ETBC7...
  view full answer...
• Will the Curt Trailer Hitch # C13042 Fit a 1998 Chevy Pickup 1500
  The Curt Trailer Hitch Receiver # C13042 that you referenced is a confirmed fit for your 1998 Chevy 1500. If looks like when you selected your vehicle you chose "1998 Chevrolet C-Series Medium Duty" instead of the "1998 Chevrolet C/K Series Pickup" catagory that your 1500 falls under. If you will be using this trailer hitch to tow lighter trailers that don't utilize brakes then you will also want to install the Tekonsha T-One # 118315 to activate the basic trailer lighting functions....
  view full answer...
• Wiring a Brake Controller on a 1995 Chevrolet Silverado 2500 LS
  Yes, you will be able to install the Draw-Tite Activator IV Brake Controller, item # 5504, on your 1995 Chevrolet 2500 Silverado LS. You will not need the Universal Brake Control Wiring Adapter 1999-02 Chevrolet, GMC, Cadillac, item # 3025-S, on the 1995 model because there is no factory port under the dash to plug the adapter in to. Chevrolet did not start putting the brake controller wiring port under the dash until 1999 so you will need to hard wire the brake controller on your 1995...
  view full answer...

Do you have a question about this Custom Fit Vehicle Wiring?