# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Ball mount works perfect with my hitch. Great product!
Good product.. Only wish it came with the pin to hold it into the hitch
# 2
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
Perfect fit on my car. I was worried I was going to have a hard time getting the right hitch and wiring harness, but thanks to etrailer, I didn't have a single hiccup. I was worried about not getting it in time for my cross country journey in which I will be needing to pull a small trailer. I ordered the hitch with only about a week before I'm supposed to start my drive and got everything within just a few days! Great all around. Really took the guesswork out of all of this. Thank you guys
Solid build. Slid right in and is solid as a rock.
# 3
Curt Vertical 2" to Fixed Ball Mount - 12-3/8" Long, 2-1/4" Rise
Purchased for a Dodge Journey with vertical mount hitch. Waited 5 months to get one from Chrysler and finally gave up found this one online. Sturdy design and does what I need it to. My only complaint is there is no recessed slot for the hitch ball to screw in tightly.
Tried to get this from the Dodge who put on the hitch. After six weeks of waiting I called you and got it in two days. Thanks.
# 4
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
I installed this on my 2015 Honda Accord for the purpose of pulling my small aluminum fishing boat and trailer. Works great!
Drawbar looks great and will be using in next two days. Thanks!
# 5
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Ball mount works perfect with my hitch. Great product!
Good product.. Only wish it came with the pin to hold it into the hitch
# 6
MaxxTow Ball Mount w/ 2" Accessory Receiver - 2" Hitches - 2-1/4" Drop - 5,000 lbs
Heavy duty , very good quality.
# 7
Gen-Y Adjustable 2-Ball Mount w/ Stacked Receivers - 2-1/2" Hitch - 12" Drop/Rise - 32K
Its stout and pulls my 7X16 foot enclosed trailer, fully loaded with 8,000 pounds, without any issue. I don't even know that its back there. I have a diesel Ram 2500 with an 8 inch lift and the hitch drops level with the trailer. 5 stars!!
Haven't used it yet but it looks great! 19 f250 with 8" lift and 37's. The 12 drop is perfect
# 8
Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 9-3/4" Long - 3,500 lbs
This draw bar in perfect for my John Deere X738 tractor. What I like about it is the ¾” rise it keep the draw bar height at about the same as the factory frame so the attachments height remain level. Thanks for the great product.
Not much you can say about a bar with a piece of flat metal welded to it; well made looks good. What is really important is that e-trailer is fast, friendly and knowledgeable. I've ordered from them anytime I needed a trailer/RV part.
# 9
B&W Tow & Stow 3-Ball Mount - 2.5" Hitch - 7" Drop/7.5" Rise - 18K - Black
I purchased this hitch for my 2024 GMC Sierra 3500 which has the multiple tailgate. The hitch was in the stow position but still damaged my tailgate when I had the tailgate fully down and used the step feature. it bent the metal and scratched the paint. So please be aware this hitch is not recommended for the 2024 GMC sierra 3500 with multiple tailgate.
About a year ago, I bought a new to me truck that needed a 2.5" hitch. I love this 3 in 1 setup. I really like that it stows and I can always have it back there. I haven't used the 1 7/8" yet, but there are plenty of old trailers out there that would need it at some point. I have used the 2" & 2 5/16" plenty. It's sturdy, looks good, and is super convenient, what's not to like about it.
# 10
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.
Quality is excellent. However, it did not work so I am not sure what to do with it. I thought I could use the top hitch for a Bike rack and pull a utility trailer with other toys. The trailer is too close to make a turn so good try but not able to use it. Thank you for asking. I did not open the box for a while because I was having the trailer worked on so assumed I waited too long to return.
# 11
Cushioned Ball Mount for 2" Hitches - 4-3/4" Rise - 6" Drop - 10,000 lbs
Its was the right drop for the height of my truck, and works as well and maybe even better than my last hitch. I think it might be do to the covert a ball I am using with it which lets me tow different trailer with different size ball's.
All of the items arrived on time and not damaged in any way. Excellent quality products.
# 12
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
I have a custom made tow guard. The ball mount I have was too short to allow me to attach the tow guard to my new truck. I searched the web and found just what I needed at etrailer.com. It's the only site I found that carried the size I needed. The product fits my needs perfectly. I can now protect my boat from rocks and other road debris when towing. Thank you etrailer.com.
# 13
Rapid Hitch Adjustable, Aluminum Ball Mount Kit w/ 2 Zinc Balls - 10" Drop, 11" Rise
Hello The hitch works great as viewed in the enclosed pictures. If inverted it hits the bumper, of my Dodge 2500. The section that goes into the receiver is about 1/2" too short and hits the bumper. I have not tried it on my other vehicle to see if this is a problem. Kind Regards Leon D
A VERY nice piece that will set your mind at ease. Easy to adjust height. The ONLY thing I wish is there was an option to have different sized ball combinations. I mainly use 2" and NEVER use a 2 5/16"(or whatever the larger size is) and would prefer to have a 1 7/8" on the other side.
# 14
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 9-3/8" Long - 3,500 lbs
I needed to tow a trailer with a 2" ball. My original ball mount has a 1 7/8" ball installed. I had previously tried to change a ball on a hitch and destroyed the nut and damaged the underside of the ball mount. The lock washer had done a great job in keeping the nut from coming off. I dreaded trying to remove my 1 7/8" ball to install a new one that I would only use once. I decided to buy a new ball mount and mount the new 2" ball. This ball mount is so inexpensive that I realized I could have both ball sizes permanently mounted for use in either ball size.
I wasn't sure what type of ball mount I needed for my new Mazda CX-9, so I had to call a representative. The first time I called, the very knowledgeable gentlemen told me exactly how to measure my SUV to figure out the drop I needed. I called back the next day and talked to a lady who helped me figure out exactly what I needed. This is my second purchase from etrailer. The first was a hitch for my old Honda Odyssey, which was also a great experience. The employees are so helpful, the video tutorials on the web site are fantastic and the prices are great. etrailer.com is the first place I go to look for trailer and towing supplies!
# 15
Draw-Tite Ball Mount for 2" Hitches - 1" Rise, 2" Drop - 8-1/2" Long - 16K
This is a beast of a drawbar, solid forged steel & well finished. It's also very heavy and E-Trailer needed to ship 3 times because the first two broke out of the box they were packed in. (Someone in the USPS has a couple nice draw bars.) Fortunately the 3rd effort was much better packed in a reinforced box and was successfully delivered. E-Trailer customer service was exemplary in resolving the shipment issue & I will definitely shop with them again.
I had a great experience ordering from you. Your organization kept me completely up to date with the order & shipping process and delivered the exact products I ordered. Attached is a photo of the 16,000 lbs capacity hitch and 30,000 lbs 2 5/16 ball you sold me in use. The boat and trailer total about 12,000 pounds. Thanks again.
# 16
Curt Heavy Duty Forged Ball Mount with 2-5/16" Ball - 2" Drop - 15,000 lbs
I tried twice to get this hitch and ball from [online vendor]. Twice the shipment was lost and I had to get a refund. Shipment from etrailer is right the first time and arrived quickly. Plus, since the ball is already torqued on the ball mount, I don't need to by a large socket.
We’ve already installed it and hitched up the horse trailer. Works great for my needs. Half the weight of the much heavier weight distribution system we had been using (and will continue to use for Interstate travel). Hook up was fast and easy.
# 17
Curt Class III Ball Mount with 1-7/8" Ball - 4" Drop - 3,500 lbs
Perfect fit on my car. I was worried I was going to have a hard time getting the right hitch and wiring harness, but thanks to etrailer, I didn't have a single hiccup. I was worried about not getting it in time for my cross country journey in which I will be needing to pull a small trailer. I ordered the hitch with only about a week before I'm supposed to start my drive and got everything within just a few days! Great all around. Really took the guesswork out of all of this. Thank you guys
I have purchased my trailer hitch, ball mount and hitch locks for my 2017 Dodge Journey. The service and products from this company have been top notch and I plan on using them in the future. Thanks again for a service that is increasingly hard to come by these days.
# 18
Curt Class III Drawbar - 2" Rise - 4" Drop - 13" Long - 7,500 lbs
Haven't used it yet. I bought it because of CURT's quality. It was beat up in shipping though.
Exactly what I needed to extend the reach of the ball beyond my rear tire carrier WITHOUT losing any tongue weight capacity! I used mine for the 2" rise.
# 19
Channel Style Adjustable Ballmount - 2" & 2-5/16" Balls - 14,000 lbs
This hitch has worked out great for me over the last year. It’s very heavy duty and easy to adjust. I’ve hauled a 9,000 lb boat, long-distance on numerous occasions without issue. I also haul a landscape trailer on a daily basis weighing over 5,000lbs and haven’t had a single issue. Great hitch that was significantly cheaper than others and is very high quality. I’ve recommended it to several people and I wouldn’t hesitate to buy again. The only thing I would like to have now in a hitch is a tongue weight gauge, but it isn’t necessary.
This is a great hitch. Highly recommend this hitch. This is my second curt hitch, first one was on my ford f450 but unfortunately that one wouldn’t fit on my new truck, do to shank size.
# 20
Curt Channel Style Adjustable Ballmount - 5-1/4" Rise, 6-3/4" Drop - 6,000 lbs
New GMC AT4 required a new ball mount and this one fit all the requirements for the truck and new multi-pro tailgate. With the AT4, I needed more drop and a longer shank (12" hole) for the tailgate to not hit my trailer jack stand; plus, the multiple drop adjustments will make changing trailers a snap. Great product from Curt and great service from etrailer (as usual).
This is a great ball mount. Fits the Class III hitch on my Explorer perfectly. Works well with my locking anti-rattle pin. However, there is a little noise from the dual pins used for the adjustment. I called etrailer’s customer service to inquire about remedies for this and was told that there is an Allen key adjustment that needs to be tightened to reduce the noise. I have yet to tighten it but other than that, the ball mount has done a great job.
What our customers are saying:
"Very helpful/friendly Customer Service. Competitive Pricing. Shipping was Fast."