# 1
Draw-Tite Drawbar for 1-1/4" Hitches - 4" Rise - 10" Long - 2,000 lbs
works well brings the trailer tongue up to level. I have it on an EV so the raddle is annoying, because I just keep on forgetting to buy a anti rattler.
This is very sturdy hitch. It is made of solid steel, not tubing. It will be used on my Mazda RX-3 to tow my car dolly to the RV lot where I will swap everything around and the car will end up on the dolly behind my RV.
# 2
B&W Tow & Stow 2-Ball Mount - 2-1/2" Hitch - 7-1/2" Drop/Rise - 18K - Black
Went with the B&W due to the length of the shaft going into the receiver. My 2024 Ram's receiver is recessed under the bumper. This hitch is long enough to accept my Towtector product. Similar to Rock Tamers. Also, Brittany in customer service was awesome to work with as she guided me towards the product that worked for my application.
I love being able to switch ball sizes so easy. Still looks good after a year. 2016 F250 2.5 inch lift. Sometimes the hitch scrapes is the only con I have.
# 3
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
I have a custom made tow guard. The ball mount I have was too short to allow me to attach the tow guard to my new truck. I searched the web and found just what I needed at etrailer.com. It's the only site I found that carried the size I needed. The product fits my needs perfectly. I can now protect my boat from rocks and other road debris when towing. Thank you etrailer.com.
# 4
Draw-Tite Ball Mount - 3/4" Rise, 2" Drop - 10-1/2" Long - 6,000 lbs
This thing is a beast! The welds are perfect! This will never break. You will probably never need to buy another. I wish I could write more but, hey, It's a ball mount. Nuff said.
Product is well built. I needed an antisway tab on the opposite side from the product pictured online, so I called and asked whether etrailer had a separate tab that I could weld where I needed it. Etrailer had it and the two items arrived very quickly by mail. I now have the ball height I wanted and a good short distance from ball to bumper--and the antisway tab ball mount. The setup should be just right for towing my 16' Casita with the Chevy Trail Blazer.
# 5
Draw-Tite Ball Mount for 2" Hitches - 1" Rise, 2" Drop - 8-1/2" Long - 16K
This is a beast of a drawbar, solid forged steel & well finished. It's also very heavy and E-Trailer needed to ship 3 times because the first two broke out of the box they were packed in. (Someone in the USPS has a couple nice draw bars.) Fortunately the 3rd effort was much better packed in a reinforced box and was successfully delivered. E-Trailer customer service was exemplary in resolving the shipment issue & I will definitely shop with them again.
I had a great experience ordering from you. Your organization kept me completely up to date with the order & shipping process and delivered the exact products I ordered. Attached is a photo of the 16,000 lbs capacity hitch and 30,000 lbs 2 5/16 ball you sold me in use. The boat and trailer total about 12,000 pounds. Thanks again.
# 6
etrailer 2-3/4" Rise or 4" Drop Ball Mount Kit - 7,500 lbs
I purchased the etrailer.com 2-3/4 " Rise or 4" Drop Ball Mount Kit, Curt Trailer Hitch Receiver and Twist-in 7-Pole RV-Style Trailer Connector for my 2011 Chevy Silverado. Quick Delivery! All the necessary parts arrived in perfect condition. Directions were spot on and the instructional videos were great.
The drop ball mount is the perfect size for my Jeep. The versatile hitch balls are convenient. Thank you for putting together a great kit, providing excellent communication, and delivering it quickly.
# 7
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
Works great with my Blazer pulling my pop up camper.
Looks like a nice piece of work, and works great, just bought a utility trailer and brought back home.. Works like a champ..
# 8
Draw-Tite Ball Mount w/ 2" Ball for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
This thing is a beast! The welds are perfect! This will never break. You will probably never need to buy another. I wish I could write more but, hey, It's a ball mount. Nuff said.
Product is well built. I needed an antisway tab on the opposite side from the product pictured online, so I called and asked whether etrailer had a separate tab that I could weld where I needed it. Etrailer had it and the two items arrived very quickly by mail. I now have the ball height I wanted and a good short distance from ball to bumper--and the antisway tab ball mount. The setup should be just right for towing my 16' Casita with the Chevy Trail Blazer.
# 9
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 9-1/4" Long - 7,500 lbs
Looks like a nice piece of work, and works great, just bought a utility trailer and brought back home.. Works like a champ..
Works great with my Blazer pulling my pop up camper.
# 10
Gen-Y Torsion 2-Ball Mount w/ Stacked Receivers - 2" Hitch - 12-1/2" Drop - 16K
anyways thus far it's a #5 I haven't really used it but I will sooner than later. Your hitch is on this bad boy!! Thank you for considering my 2020 Ford Velocity Blue F350 Lariat Special addition!!!
The order process was smooth. But, when trying to find out about the the lifetime warranty offered by Gen Y on the rubber components in the hitch Nicole could not answer my question. I asked if I was able to purchase through you and if not could I purchase from Gen Y even though I bought the hitch from you. This is something customer service should know the answer too. You would have gotten five stars but it was ruined by lack of knowledge by your staff.
# 11
Curt Pintle Hook with 2" Ball - for 2" Hitches - 10,000 lbs/16,000 lbs
This is an excellent hook. And it looks killer. etrailers exceptional service and quality is beyond compare.
Looks great
# 12
Curt Slim Adjustable 2-Ball Channel Mount - 2" Hitch - 3-3/4" Drop, 3-1/2" Rise - 10K
Terrri was great. She was able to hunt down the very specific items I needed for my business and did it while being pleasant and professional. I was looking for these items for a few days before I contacted etrailer. I had my item in time for the event I needed it for and I wouldn't go anywhere else if the need for anything to do with my trailer arises again. Thank you Terri, great job!!
Shipping was fast,the Curt adjustable mount is sturdy and everything worked easily,fits my Chevy Colorado Zr2 perfectly
# 13
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
I am very pleased with the hitch, ball mount, and electrical package. All were easy to install if you follow the easy to understand directions. An added plus for putting one of these on a MINI is that the hitch can be hidden behind the "black plate/cover" that is on the rear bumper. It looks just like it came out of the factory except when to need to install the ball mount. The service has been outstanding. This is the place to go.
# 14
Brophy Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 13-1/4" Long - 10K
Slightly longer, so you can open your tailgate with a cargo trailer attached. Trailers with a tongue jack that is forward are problematic for tailgates...
I’m pleased with the product and how prompt the delivery was. However the packaging was insufficient and the packaging was torn open all over. Scuffing of the finish is a result and of little consequence due to the intended use. It’s a stinger w/ball for motorhome. May I suggest better packaging in the future
# 15
Curt Multi-Ball Adjustable Ball Mount for 2" Trailer Hitches
Picked up my teardrop in ABQ on 2/17/23, and the Curt ball mount lined up perfectly with no drop/rise, and the extra length gave clearance for my rear door mounted spare tire. This mount is a beast, and the "overbuilt" nature of it gave me confidence that my Bronco would tow the teardrop easily. I also got the Curt Echo wireless brake controller, which synced easily to my phone and was easy to install, set up, and use. Overall a great towing experience, thanks to etrailer and Curt!
Very versatile - can use it on both my vehicles that have very different hitch height. Clean welds, super solid. Weighs a LOT!
# 16
Convert-A-Ball Cushioned Multi-Hitch Clevis and Pintle Hook Combo w/ 3 Balls - 2" Hitches - 10K
No problems with the hitch- makes it easy to switch between trailers! I have no complaints!
Very good product and I would have given it a 5 star rating but there is one critical flaw that is quickly remedied. When using the pintle hitch, the pressure exerted on pin while pulling a load can cause the pin to turn, thereby popping out the keeper pin. This happened twice and it was a good thing that I had the hitch positioned so that the pintle pin was installed going down allowing gravity to hold the pin in place even when the keeper pin fell out. I have since changed out this style of keeper pin with a cinch pin that can spin 360 degrees inside the 2" tube and no pressure is exerted on it by the load being pulled. If I were designing this from new, I would make it so that the draw pin on the pintle had a square shoulder much like a carriage bolt so that it can't turn thereby eliminating pressure on the keeper pin. Other than that it is a great product.
# 17
Gen-Y Adjustable 2-Ball Mount w/ Stacked Receivers - 2-1/2" Hitch - 15" Drop - 21K
This thing is a monster. I installed it on a chevy 2500 with a 6.5" lift and 37" tires. With 5 different height options I can not imagine any trailer i couldnt keep level. The best part is no more changing hitches just changing the hight. Also, the pintle adapter is an amazing addition too. It's so simple to use and works great. This hitch is expensive but totally worth it.
Great products, great service, quick and really good priced shipping
# 18
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
Ordered this hitch and it worked perfect for what I needed just bought a teardrop trailer. Couldn't open up the tailgate on my Jeep so I ordered this extended hitch and I brought the ball out past my spare tire and the tailgate opens up now I have no problems. And I looked everywhere couldn't find one of this quality and at this price very reasonable the other ones hundreds of dollars didn't want to spend that much.
This was the longest hitch ball mount I could find anywhere. I used it with a short extension for my 2021 T G so that I could open the back doors without hitting the trailer wheel crank. With my new trailer, Intact Flyer Discover, I don't need the extension and can still open the doors. Works well.
# 19
MaxxTow Ball Mount w/ 2" Accessory Receiver - 2" Hitches - 2-1/4" Drop - 5,000 lbs
Heavy duty , very good quality.
# 20
Reese Tri-Ball Trailer Hitch Ball Mount with Clevis Hook - 10,000 lbs
Holding up well and hauling my two trailers smoothly and as needed. No issues at the one year mark. Mainly haul a 17ft flat trailer with a small 25hp tractor, and a 10ft dump trailer. Does a good job of shin knocking when you walk by. Have yet found to find a good enough reason to use the clevis hook. :(
I pulled a uhaul tow dolly with a PT cruiser from Hattiesburg, MS to Cave City, AR. No problems.
Draw-Tite Ball Mount Review - 1999 Chevrolet Blazer
(Music) Today on our 1999 Chevrolet Blazer we'll be test fitting a ball mount from Draw-Tite with a three-quarter rise and 2 inch drop, rated at 7500 pounds, part number 2923. To begin our test fit we'll go ahead and get our hitch height. This is the measurement from the ground to the inside top edge of our receiver tube. Our hitch height is 16 inches. Now we'll take our ball mount and install it in the drop position. Our measurement from the ground to the top of the ball platform is thirteen and a half inches.
What our customers are saying:
"You folks are fast. Thank you very much."