What our customers are saying:
very easy to shop
Mike
Richmond, CA
Search For Custom Fit Chevrolet HHR AccessoriesSelect A Category Below
Towing
Chevrolet HHR Trailer Hitch
Chevrolet HHR Trailer Wiring
Chevrolet HHR Brake Controller
Chevrolet HHR Base Plate for Tow Bar
Chevrolet HHR Vehicle Tow Bar Brake System
Chevrolet HHR Vehicle Tow Bar Wiring
Cargo Control
Chevrolet HHR Roof Rack
Chevrolet HHR Trunk Bike Rack
Performance Accessories
Chevrolet HHR Cold Air Intake
Chevrolet HHR Air Filter
Chevrolet HHR Exhaust
Chevrolet HHR Suspension Enhancement
Chevrolet HHR Performance Chip Tuners
Chevrolet HHR Vehicle Lights
Chevrolet HHR Tire Chains
Chevrolet HHR Fluid Filters
Chevrolet HHR Catalytic Converters
Chevrolet HHR Vehicle Engine Heaters
Chevrolet HHR Radiator Fan
Chevrolet HHR Cabin Air Filter
Vehicle Trim
Chevrolet HHR Floor Mats
Chevrolet HHR Vehicle Covers
Chevrolet HHR Bug Shield
Chevrolet HHR Side Window Vents
Chevrolet HHR Lamp Guards
Chevrolet HHR Vehicle Tent
Chevrolet HHR Vehicle Seat Covers
Chevrolet HHR Replacement Mirrors
Chevrolet HHR Windshield Wiper Blades
Chevrolet HHR Windshield Covers
Chevrolet HHR Vehicle Air Mattress
Roadmaster Universal Diode Wiring Kit Installation - 2009 Chevrolet HHR
Speaker 1: Today on this 2009 Chevrolet HHR you'll be having a look at and being shown how to install the Roadmaster Universal Hy-Power Diode Wiring Kit, part number RM-152. We will also be using a Roadmaster six wire trailer connector, part number RM-910030-7.Here's what our diode wiring kit looks like installed. What this is gonna allow us to do is safely and legally flat tow our vehicle behind our motor home without having to worry about using any magnetic tow lights. This will use the existing light bulbs in our vehicle with very little modification required. You're already using what you have there. What the diodes are gonna do is protect our vehicle's expensive lighting circuit.
Roadmaster Diode 7 to 6 Wire Coil Kit Installation - 2007 Chevrolet HHR
Today in our 2007 Chevrolet HHR, we'll be installing the Roadmaster Diode 7 wire to 6 wire flexo-coil wiring kit, part number RM-15267. Here's what a wiring kit comes with. Most importantly, we have our connector here. This will be our umbilical between our RV and our vehicle in tow. The 7 way goes towards the 7 way on the back of the RV, and the 6 way here will go to the front of our vehicle right here on this connector. This will allow us to have all of our lighting circuitry on the vehicle work in conjunction with the motor home, and because this uses diodes, there's no extra bulbs and sockets.
Blue Ox Tow Bar Wiring Kit Installation - 2011 Chevrolet HHR
Today on our 2011 Chevrolet HHR, we're going to take a look at and also show you how to install the Blue Ox 4-Diode Tow Bar Wiring Kit. Part number is BX8848. All right, here's what the diode kit's going to look like minus that 26' length of wire that we've already ran. Now the diodes are going to take two inputs, so we can have our towed vehicle's input and our towing vehicle's input, whether it's for running lights or whether it's for our turn signals or brakes. We have this single output coming to our factory bulb. We're going to have four of these. These are going to help to prevent backfeed from the motorhome to the car or from the car to the motorhome.
Blue Ox Fuse ByPass Switch Installation - 2011 Chevrolet HHR
Today on our 2011 Chevrolet HHR we're going to be showing you to how to install the blue ox fuse bypass switch for towed vehicle. Excepting the ATM mini fuse and ten inches long, part number is bx88271. The blue ox fuse bypass is going to be an excellent solution for those vehicles where fuses need to be removed for it to go into tow mode. Essentially what we're going to do is just replace that fuse into the fuse bypass. Then when we turn our switch in the down position it would be just like pulling that fuse out of the power block. That's going to allow us to go into tow mode without pulling this whole panel off trying to figure out which fuse it is and pull it out.
Tail Light Wiring Kit Installation - 2008 Chevrolet HHR
Today, on our 2008 Chevrolet HHR we're going to be installing the Hopkins tow bar wiring, part number HM56100. To begin our install, we're going to start at the rear of the vehicle. We need to open up the rear hatch and remove the access panels just behind the tail light assemblies. There's one on each side. I'm just going to use a flat blade screw driver, get behind it and pop it free. Behind the access panel, we can see the manufacturer's wiring as it comes into the tail light. Here from the converter box is our yellow wire connector that will ultimately plug in here behind the driver's side tail light assembly.
