2013 Kia Sorento Trailer Hitch
2013 Kia Sorento Trailer Wiring
2013 Kia Sorento Brake Controller
2013 Kia Sorento Base Plate for Tow Bar
2013 Kia Sorento Vehicle Tow Bar Brake System
2013 Kia Sorento Vehicle Tow Bar Wiring
2013 Kia Sorento Roof Rack
2013 Kia Sorento Trunk Bike Rack
2013 Kia Sorento Air Filter
2013 Kia Sorento Performance Chip Tuners
2013 Kia Sorento Vehicle Lights
2013 Kia Sorento Tire Chains
2013 Kia Sorento Fluid Filters
2013 Kia Sorento Salt Spreader
2013 Kia Sorento Vehicle Engine Heaters
2013 Kia Sorento Cabin Air Filter
2013 Kia Sorento Lift Assist
2013 Kia Sorento Floor Mats
2013 Kia Sorento Trim Kits
2013 Kia Sorento Vehicle Covers
2013 Kia Sorento Bug Shield
2013 Kia Sorento Mud Flaps
2013 Kia Sorento Vehicle Seat Covers
2013 Kia Sorento Replacement Mirrors
2013 Kia Sorento Windshield Wiper Blades
2013 Kia Sorento Windshield Covers
2013 Kia Sorento Vehicle Air Mattress
Videos
for Kia Sorento Owners
Help Articles
Expert Answers
If your 2020 Kia Sorento has the factory tow package, there will be a tail light wiring connector behind the rear tire of the driver side, on the outside of the frame rail. As shown in the attached photos, an underbody cover will need to be removed…
The most definitive way to determine if your 2013 Kia Sorento has the factory towing prep package is to have the dealer run the VIN number. They will be able to you how it is equipped. The trailer wiring for vehicles with the tow prep package,…
The Draw-Tite #75908 is more hidden with the recessed aspect of the hitch pin hole being 5-1/2 inches from the outermost part of the bumper. The height is 15-1/2 inches from the inside top of the receiver to the ground. The Curt #C13195 is very…
While we do have a video of a trailer wiring harness installation on a 2012 Kia Sorento, it is not for the Curt T-Connector Vehicle Wiring Harness #C56328. Instead, the video we have, which I have linked for you below, is of an installation of the…
If you are installing the Curt Trailer Hitch Receiver #C13073 on your 2012 Kia Sorento then it will require the following hardware: Quantity (4) M10 - 1.25 x 30 (Hex Bolt) Quantity (6) 7/16" (Conical Toothed Washer) Quantity (2) 7_16 - 14 x 4…
In most cases Loctite is not required when installing a trailer hitch, but it would not be a bad idea. I suggest using the Loctite Blue Stick Threadlocker, #LT37643, which will provide a secure grip and protect against water and grime.
The Curt Hitch #C13073 is compatible with your vehicle and allows a full size spare to be used when in installed. Check out the picture I attached that shows this hitch installed on a vehicle similar to yours and a full size spare underneath the rear…
For your 2013 Kia Sorento, the towing capacity is 3500 lb for the V6 models. I recommend the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" #75684 for your trailer hitch receiver. This will give you a 2 inch receiver…
The MaxxFan Deluxe Roof Vent w/ 12V Fan and Thermostat - Manual Lift - 10 Speed - White Item #MA00-05100K only requires 12 volt, 5 amp power to operate so based on this 12 gauge wire would be overkill but 16 gauge such as #DW02359-1 sold by the foot…
The MaxxFan Deluxe Roof Vent w/ 12V Fan #MA00-06401K only draws 5 amps so you don't need to go crazy with the wiring gauge but I would still recommend 10 gauge like part #10-1-1 (sold by foot) as it's heavier than you'd ever need and will…
Yes, a weight distribution system like the Curt TruTrack Weight Distribution System part #C17499 will add stress to both the trailer and vehicle frame. That said, this stress is not usually enough to cause damage. The only exceptions to this would be…
Ideally, you'll want some of the hardware attaching the e-track to the trailer floor to also secure to the cross members as well as to the planks that make up the trailer floor. If that's not possible, I'd recommend using a backer plate…