2004 Jeep Grand Cherokee Trailer Hitch
2004 Jeep Grand Cherokee Trailer Wiring
2004 Jeep Grand Cherokee Brake Controller
2004 Jeep Grand Cherokee Front Mount Hitch
2004 Jeep Grand Cherokee Towing Mirrors
2004 Jeep Grand Cherokee Base Plate for Tow Bar
2004 Jeep Grand Cherokee Vehicle Tow Bar Brake System
2004 Jeep Grand Cherokee Vehicle Tow Bar Wiring
2004 Jeep Grand Cherokee BOLT brand vehicle and hitch locks
2004 Jeep Grand Cherokee Roof Rack
2004 Jeep Grand Cherokee Trunk Bike Rack
2004 Jeep Grand Cherokee Air Filter
2004 Jeep Grand Cherokee Exhaust
2004 Jeep Grand Cherokee Suspension Enhancement
2004 Jeep Grand Cherokee Transmission Cooler
2004 Jeep Grand Cherokee Performance Chip Tuners
2004 Jeep Grand Cherokee Vehicle Lights
2004 Jeep Grand Cherokee Tire Chains
2004 Jeep Grand Cherokee Fluid Filters
2004 Jeep Grand Cherokee Vehicle Sway Bars
2004 Jeep Grand Cherokee Catalytic Converters
2004 Jeep Grand Cherokee Vehicle Snow Plows
2004 Jeep Grand Cherokee Salt Spreader
2004 Jeep Grand Cherokee Vehicle Engine Heaters
2004 Jeep Grand Cherokee Radiator Fan
2004 Jeep Grand Cherokee Cabin Air Filter
2004 Jeep Grand Cherokee Lift Assist
2004 Jeep Grand Cherokee Floor Mats
2004 Jeep Grand Cherokee Nerf Bars - Running Boards
2004 Jeep Grand Cherokee Trim Kits
2004 Jeep Grand Cherokee Vehicle Covers
2004 Jeep Grand Cherokee Grille Guard
2004 Jeep Grand Cherokee Bug Shield
2004 Jeep Grand Cherokee Side Window Vents
2004 Jeep Grand Cherokee Mud Flaps
2004 Jeep Grand Cherokee Vehicle Seat Covers
2004 Jeep Grand Cherokee Replacement Mirrors
2004 Jeep Grand Cherokee Windshield Wiper Blades
2004 Jeep Grand Cherokee Windshield Covers
2004 Jeep Grand Cherokee Vehicle Air Mattress
Videos
for Jeep Grand Cherokee Owners
Help Articles
Expert Answers
To flat tow your 2004 Jeep Grand Cherokee, you will need a base plate kit, a tow bar, safety cables, towed vehicle wiring, and a supplemental braking system. It is also likely that you will need a wiring extension to connect the RV's wiring with…
The Blue Ox tow bar adapter that will fit your new EAG JJKFB021 Bumper are the Blue Ox Aftermarket Off-Road Bumper Adaper - 7/8 Inch Pin #BX88357. I was able to confirm that the d-rings on your aftermarket bumper use a 7/8 inch pin and have a 1 inch…
It is pretty easy to flat tow your 2004 Jeep Grand Cherokee Limited, as long as it is a 4WD model and does not have the Quadra-Trac I. You will need a base plate kit, tow bar, safety cables, tow bar wiring, and supplemental braking system. I…
Since you do not have the tow package I am assuming you do not have a factory trailer connector. In that case I would recommend you get a Curt T-Connector Custom Fit Vehicle Wiring #C55369. This is the recommended wiring harness for the 1999-2004…
Jeep issued a recall on certain models of the Grand Cherokee and Liberty due to the issue of an exposed gas tank. Basically, the gas tank is exposed at the rear of the Jeep with very little protection and there have been reports of the gas tank…
Yes, the Equalizer Head part #EQ90-02-1000 that you referenced is the correct replacement head for the 1,000 lb tongue weight system part #EQ37100ET that you have.
The Replacement Spring Bars #EQ90-01-1099 are the correct replacement bars for your 1,000 pound Equal-i-zer weight distribution system. This will include 2 spring bars. The part #EQ90-02-1099 referenced in your question is the same product, however…
I reached out to a representative of Equal-i-zer, who told me that the sockets from the 1,200 lb tongue weight head #EQ90-02-1200 will not fit in a 1,000 lb tongue weight head #EQ90-02-1000 because they are too big. If you need additional sockets for…
The Equal-i-zer weight distribution spring bars and heads are both designed to fit specific tongue weight ratings so you'd have to replace both. So to uprate your system to 1,000 lbs tongue weight you'd need the head part #EQ90-02-1000 and…
The Replacement Socket for Equal-i-zer 1,000 Lb Weight Distribution Systems part #EQ90-03-1000 is larger than the Replacement Socket for Equal-i-zer 600 Lb Weight Distribution Systems part #EQ90-03-0600 therefore, it cannot be used with the…
If your trailer has a tongue weight of around 700 pounds then your existing 10,000/1,000 pound Equal-i-zer Weight Distribution System #EQ37100ET should be sufficient. Upgrading to a 12,000/1,200 system won't provide any additional benefits to…
The opening on the Replacement Sockets for Equal-I-zer Weight Distribution System, #EQ90-03-1000, measure just over 1-3/8 inches. The actual measurement of the opening is 1.380 inches which is very close to 1-3/8 inches.