Front Receiver Hitch Specs:
Features:
Attach accessories to the front of your vehicle with this trailer hitch receiver. Perfect for winches, spare tire carriers and more. Hidden cross tube leaves only receiver visible. Aluminum and steel alloy construction is sturdy and eco-friendly.
Installation Notes:
No drilling required for installation
Additional installation time may be required depending on the configuration of your vehicle
Grille will be temporarily removed for hitch installation
Some vehicles may have a lower grille insert which will need to be permanently removed for hitch installation
More Information >Front Receiver Hitch Specs:
Features:
Attach accessories to the front of your vehicle with this trailer hitch receiver. Perfect for winches, spare tire carriers and more. Hidden cross tube leaves only receiver visible. Aluminum and steel alloy construction is sturdy and eco-friendly.
Installation Notes:
No drilling required for installation
Additional installation time may be required depending on the configuration of your vehicle
Grille will be temporarily removed for hitch installation
Some vehicles may have a lower grille insert which will need to be permanently removed for hitch installation
More Information >Front Receiver Hitch Specs:
Features:
Easily attach a variety of accessories to the front of your vehicle with this fully welded, corrosion-resistant trailer hitch receiver. Perfect for winches, spare tire carriers and more.
Installation Notes:
No drilling required for installation
Trimming of front air dam and/or fascia may be required for installation
Tech Tip:
Bumper will need to be loosened for hitch installation.
More Information >Front Receiver Hitch Specs:
Features:
Easily attach a variety of accessories to the front of your vehicle with this fully welded, corrosion-resistant trailer hitch receiver. Perfect for winches, spare tire carriers and more.
Installation Notes:
No drilling required for installation
Trimming of front air dam and/or fascia may be required for installation
Tech Tip:
Bumper will need to be loosened for hitch installation.
More Information >Videos
for Front Receiver Hitch
Help Articles
for Front Receiver Hitch
Expert Answers
for Front Receiver Hitch
There is a suggested and common method for 6 function trailer wiring. You will have the following functions: Right Turn, Left Turn, Ground, Tail/marker, Brake, Battery. I have included a help article on trailer wiring that includes a diagram and…
view full answer...The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.
view full answer...My contact at Yates Rubber advises that a nominal 8-inch keel roller does not measure exactly 8 inches; typically they are slightly smaller than the specified size, much the way a piece of 2 x 4 lumber is not exactly 2-inches by 4-inches. I took…
view full answer...While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and…
view full answer...Hey Michael, thanks for reaching out! The EcoHitch #EH57FR sits a little higher than the Curt #C52NR so it will give you better ground clearance for your 2024 Chevy Silverado 2500. The EcoHitch is a bit more recessed into the front bumper than the…
view full answer...The factory trailer brake controller port on your 2021 Chevrolet Tahoe is located underneath the dash just to the left of the steering wheel. It will be taped to another harness so it may take a bit of looking to find. Keep in mind that if your…
view full answer...If your 2022 Chevrolet Tahoe does not have the factory tow package then the plug may not be there. If this is the case you would need to hardwire in a brake controller. If your Tahoe does have the tow package then the plug will be under the dash.…
view full answer...I do have an option for you but we have not yet gotten out hands on a 2019 Chevrolet Blazer therefore, have not had the chance to look for the brake controller wiring port either. I checked with both Tekonsha and Curt and it looks like they have…
view full answer...M12-1.5 and 1/2"-20 threads are not going to be interchangeable. The diameter of an M12 thread is only going to be 0.4724" while…
view full answer...If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly -…
view full answer...If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
view full answer...The 1-7/8 inch width is what is rounded up to 2 inches which is a standard width for winch straps. The 14 foot length is not something we carry. I recommend the Hand Winch Strap with Safety Hook, 2"…
view full answer...Filter Products (8)