Vehicle Style: 2500 and 3500 - 6-1/2 Foot Bed - without RamBox Change
Roll-Up - Hard Cover Specs:
Features:
Weather-resistant, roll-up cover keeps the gear in your truck bed secure and dry. Rolls up quickly by hand for full access to your truck bed. Aluminum slats keep cover tight and help prevent break in. Requires no drilling to install.
More Information >Roll-Up - Hard Cover Specs:
Features:
Hard, roll-up cover with heavy-duty vinyl fabric and thick aluminum slats is stylish and durable. Low-profile, self-leveling rails ensure easy install. Latches at tailgate and mid-bed offer enhanced security. Cover removes in seconds without tools.
More Information >Roll-Up - Hard Cover Specs:
Features:
The Revolver X2 tonneau combines hard cover strength and security with soft cover convenience. The heavy-duty aluminum and vinyl cover sits flush on your vehicle and rolls up for full truck bed access. Easy, no-drill installation.
More Information >Roll-Up - Hard Cover Specs:
Features:
Hard, roll-up cover with premium, 5-layer fabric and thick aluminum slats is stylish and durable. Low-profile, self-leveling rails ensure easy install. Latches at tailgate and mid-bed offer enhanced security. Cover removes in seconds without tools.
Tech Tip:
Optional Stake Pocket Covers (TX22AR) available for installation (sold separately).
More Information >Soft Camper Shell Cover Specs:
Features:
The Supertop for Truck 2 features an improved design that allows for 1-person operation and features removable fabric side panels. When not in use, the top and side panels can be stored in a convenient built-in storage system. Black Diamond fabric.
Installation Notes:
No drilling required for installation
More Information >Soft Camper Shell Cover Specs:
Features:
Soft tonneau covers bed and easily rolls up to allow full truck bed access. Requires an existing Supertop for Truck 2 Tops setup (sold separately). Heavy-duty fabric constrution with EZ-Roll and bow system. Simple installation.
Installation Notes:
No drilling required for installation
More Information >Videos
for Tonneau Cover
Help Articles
for Tonneau Cover
Expert Answers
for Tonneau Cover
The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.
view full answer...Hi Jeff; thanks for the question and sturdy is definitely a good word for the etrailer tonneau that fits your 2022 Ram 1500 with a 5-1/2 foot bed, the etrailer Hard Tonneau Cover #e35DR.…
view full answer...The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.
view full answer...The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.
view full answer...Your 265/70R17 size tire is around 31-1/2 inches in diameter. You want to make sure the tire cover you get is large enough and…
view full answer...The Tow Ready wiring harness #118571 is rated for 7.5 amps for brake lights and turn signals and 7.5 amps total for running lights. The fuse that goes on the power wire connection to the battery is a 10 amp fuse. The wire gauge of the long 12 volt…
view full answer...Actually our etrailer.com brand brake assemblies are rebranded AxleTek assemblies. So we have the 8k left and right assembly set #AKEBRK-8 which is most likely what you need but these are 12-1/4 inch in diameter by 3-3/8 inches wide and attach with…
view full answer...Because the Retrax PRO MX Tonneau Cover #RT80467 for the 2019 Chevy Silverado 2500 covers the bed rails, you would not be able to use a ladder rack like the Thule TracRac #TH27000XT since that rack requires the use of the bed rails. The only…
view full answer...Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…
view full answer...Unfortunately there are no plug-in adapters or harnesses that would allow you to replace the factory 4-way flat trailer connector with a 7-way or a 7-way and 4-way connector on your 2005 Ford F-150. To complete the installation for a brake…
view full answer...There is a solution for you, but the lift kits you referred to such as #K71-725-02 will not work with welded on torsion axles. The best option is for you to simply remove your torsion axles and use the Timbren Axle-Less Trailer Suspension System…
view full answer...Yep, you're exactly right; the distance from the center of the hitch pin hole to the welded gusset is indeed four inches on…
view full answer...