Anti-Sway Bars Specs:
Features:
...powder coat Mounting brackets and end links finished in corrosion-resistant, black powder coat Made in the USA Specs: Bar diameter: 1-1/8" Limited lifetime warranty Note: Installation requires Hellwig
Installation Notes: No drilling required for installation Product is designed for vehicles at the stock height If your vehicle does not have a factory hitch, mounting kit HE77GR will be required: sold separately
Anti-Sway Bars Specs:
Features:
Minimize sway and improve the stability and driveability of your truck. Solid, 1-1/8" chromoly sway bar provides improved handling and safety. Adjustable anti-sway bar lets you choose level of stiffness. For trucks with 2" to 4" lifts.
Installation Notes:
No drilling required for installation
Product is designed for vehicles that have been lifted 2" to 4"
More Information >Videos
for Anti-Sway Bars
Help Articles
for Anti-Sway Bars
Expert Answers
for Anti-Sway Bars
The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…
view full answer...On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…
view full answer...For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…
view full answer...The number you provided, "7753400" is a patent number which corelates to…
view full answer...The Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets #RM47MR typically comes centered and you would only need to make adjustments after installation and testing to see if it continues to pull. If you adjusted it all the way out to…
view full answer...When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric…
view full answer...The torque spec for the rear U bolts on your 2019 F53 motorhome are dependent on the size. If you have 3/4 x 16 u bolts (and used a 1 1/8" socket to remove the…
view full answer...Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are…
view full answer...Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be…
view full answer...On oil bath hubs the seals are different than standard grease seals. The correct replacement for what you have is #91030. Unitized oil seals like this have a part that stays fixed and a part that rotates with the hub for optimum leak protection. I…
view full answer...The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.
view full answer...The amount of bow that's put into trailer axles like the #7359765 is based on about how much a trailer is typically going to weigh that has a 3,500 lb capacity. So…
view full answer...Filter Products (4)
Contact and Help
What our customers are saying:
In these days of customer "no service" I am usually disapointed when doing business with people I don't know. It was refreshing doing business with you. I'm impressed!
Randy
Watkinsville, GA