Anti-Sway Bars Specs:
Features:
...installed rear anti-sway bar, or as an addition if the rear anti-sway bar is not supplied....
Installation Notes:
No drilling required for installation
Product designed for 4-Wheel Drive models
Product is designed for vehicles at the stock height
More Information >Anti-Sway Bars Specs:
Features:
Minimize sway and improve the stability and driveability of your truck. Solid, 1-1/8" chromoly sway bar provides improved handling and safety. Adjustable anti-sway bar lets you choose level of stiffness. Easy, bolt-on installation.
Installation Notes:
No drilling required for installation
Product designed for 4-Wheel Drive models
Product is designed for vehicles at the stock height or have been lifted up to 2"
More Information >Anti-Sway Bars Specs:
Features:
...the factory installed rear anti-sway bar, or as an addition if the rear anti-sway bar is not supplied....
Installation Notes:
No drilling required for installation
Product designed for 2-Wheel Drive models
More Information >Anti-Sway Bars Specs:
Features:
Minimize sway and improve the stability and driveability of your truck. Solid, 1-1/8" chromoly sway bar provides improved handling and safety. Adjustable anti-sway bar lets you choose level of stiffness. For trucks with 4" to 6" lifts.
Installation Notes:
No drilling required for installation
Product designed for 4-Wheel Drive models
Product is designed for vehicles that have been lifted 2" to 4"
More Information >Anti-Sway Bars Specs:
Features:
Minimize sway and improve the stability and driveability of your truck. Solid, 1-1/4" chromoly sway bar provides improved handling and safety. Adjustable anti-sway bar lets you choose level of stiffness. Easy, bolt-on installation.
Installation Notes:
No drilling required for installation
Product designed for 2-Wheel Drive models
More Information >Videos
for Anti-Sway Bars
Help Articles
for Anti-Sway Bars
Expert Answers
for Anti-Sway Bars
The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…
view full answer...For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…
view full answer...The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex…
view full answer...The Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets #RM47MR typically comes centered and you would only need to make adjustments after installation and testing to see if it continues to pull. If you adjusted it all the way out to where…
view full answer...When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…
view full answer...The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…
view full answer...I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…
view full answer...The torque spec for the rear U bolts on your 2019 F53 motorhome are dependent on the size. If you have 3/4 x 16 u bolts (and used a 1 1/8" socket to remove the nuts) then they torque to 250 lb-ft. If the u bolts are 7/8 x 14 (and you used a 1…
view full answer...The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…
view full answer...If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…
view full answer...Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…
view full answer...On oil bath hubs the seals are different than standard grease seals. The correct replacement for what you have is #91030. Unitized oil seals like this have a part that stays fixed and a part that rotates with the hub for optimum leak protection. I…
view full answer...