Vehicle Suspension Specs:
Features:
1,000-lb Capacity. Upgrade your vehicle's front suspension with these maintenance-free helper springs. Sturdy microcellular urethane springs cushion bumps and help support a heavy load to level your ride and minimize sway. No-drill installation.
Installation Notes:
No drilling required for installation
More Information >Vehicle Suspension Specs:
Features:
1,000-lb Capacity. Upgrade your vehicle's front suspension with these maintenance-free helper springs. Sturdy microcellular urethane springs cushion bumps and help support a heavy load to level your ride and minimize sway. No-drill installation.
Installation Notes:
No drilling required for installation
More Information >Vehicle Suspension Specs:
Features:
1,000-lb Capacity. Upgrade your vehicle's front suspension with these maintenance-free helper springs. Sturdy microcellular urethane springs cushion bumps and help support a heavy load to level your ride and minimize sway. No-drill installation.
Installation Notes:
No drilling required for installation
More Information >Vehicle Suspension Specs:
Features:
...factory suspension to keep your vehicle level and improve your driving experience. The Timbren system comes with custom-fit brackets that are bolted onto each frame rail above your front axle. Hollow rubber...
Installation Notes:
No drilling required for installation
More Information >Vehicle Suspension Specs:
Features:
...factory suspension to keep your vehicle level and improve your driving experience. The Timbren system comes with custom-fit brackets that are bolted onto each frame rail above your front axle. Hollow rubber...
Installation Notes:
No drilling required for installation
More Information >Vehicle Suspension Specs:
Features:
...factory suspension to keep your vehicle level and improve your driving experience. The Timbren system comes with custom-fit brackets that are bolted onto each frame rail above your front axle. Hollow rubber...
Installation Notes:
No drilling required for installation
More Information >Vehicle Suspension Specs:
Features:
...span>Suspension Support A heavy front load can cause front-end sag as your factory suspension compresses under the weight of the load. This means that the front axle is trying to support not only the extra load...
Installation Notes:
No drilling required for installation
More Information >Vehicle Suspension Specs:
Features:
...span>Suspension Support A heavy front load can cause front-end sag as your factory suspension compresses under the weight of the load. This means that the front axle is trying to support not only the extra load...
Installation Notes:
No drilling required for installation
More Information >Vehicle Suspension Specs:
Features:
...span>Suspension Support A heavy front load can cause front-end sag as your factory suspension compresses under the weight of the load. This means that the front axle is trying to support not only the extra load...
Installation Notes:
No drilling required for installation
More Information >Videos
for Vehicle Suspension
Help Articles
for Vehicle Suspension
Expert Answers
for Vehicle Suspension
Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit…
view full answer...If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…
view full answer...For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the…
view full answer...The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the…
view full answer...It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression…
view full answer...Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be…
view full answer...I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…
view full answer...What…
view full answer...If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…
view full answer...Your trailer looks awesome! The Road armor equalizers #LC696740 and Equa-Flex Cushioned Equalizers #LC279687 are both pretty similar in performance even though the Road Armor has two dampers. The main difference is the size of the equalizers. The…
view full answer...From what I could find it looks like your 122R (red) and 122Y (amber) lights measure…
view full answer...I do have an option for you, but we do not carry the Dexter 072-027-00 you mentioned. However we do have the etrailer Double-Eye Spring for 7,000-lb Trailer Axles -…
view full answer...