Truck Bed Slide Specs:
Features:
Stop crawling into your truck bed to grab your groceries, coolers, and other hard to reach items. Sliding tray extends past the tailgate for easy access to all your gear. Fastens to existing floor board anchor points with no drilling required.
More Information >Truck Bed Slide Specs:
Features:
Stop crawling into your truck bed to grab your groceries, coolers, and other hard to reach items. Sliding tray extends past the tailgate for easy access to all your gear. Fastens to existing floor board anchor points with no drilling required.
More Information >Truck Bed Slide Specs:
Features:
Stop crawling into your truck bed to grab your groceries, coolers, and other hard to reach items. Sliding tray extends past the tailgate for easy access to all your gear. Fastens to existing floor board anchor points with no drilling required.
More Information >Truck Bed Slide Specs:
Features:
Slide-out truck bed tray lets you get gear without climbing or crawling. Steel-framed, laminated plywood deck extends smoothly - 100 percent of its length - on sealed bearings. Aluminum sides have built-in tie-down tracks. 2,200 Lbs capacity.
More Information >Videos
for Truck Bed Slide
Help Articles
for Truck Bed Slide
Expert Answers
for Truck Bed Slide
I looked up pictures of the taillights that are on the 3110 Featherlite trailers and for the LED version of them you would want the part #STL36RB and #STL37RB. It looks like the spare tire mounts for your trailer are something you would have to get…
view full answer...I do have an option for you, but we do not carry the Dexter 072-027-00 you mentioned. However we do have the etrailer Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long #e64SR which will be…
view full answer...On single axle trailers typically you put the hanger spacing right at 1/4 of an inch shorter than the leaf spring length from eye to eye center. So if you were using the leaf spring part #e54SR that you referenced which measures 25-1/8 inches long…
view full answer...For your AL-KO 7210 braking assembly, you can use the Hydraulic Brake Kit #AKFBBRK-7 as a replacement. These braking assemblies measure 12" x 2", bolts onto a 5 bolt mounting flange, will work with…
view full answer...I have spoken with Lippert about the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System part #LC675817 in they past and they informed me that the most important aspect is that the battery/batteries are sufficiently charged, between…
view full answer...The caliper bracket you are looking for is the Replacement Mounting Bracket #KCMB12D which is compatible with the 5 bolt mounting flange you have as well as the 225 Kodiak Dacromet calipers you have as well. Then for a bolt kit…
view full answer...The typical tire should run about 158 degrees (Farenheidt) once you get going down the road, but this can vary greatly depending on the weight of the trailer, how fast you're traveling, and also driving habits. So while 158…
view full answer...What you are wanting to do is very possible with the GO Power Solar Panel kit part #34273836. You could mount it on your pin box and then run the wiring to your batteries via an SAE connector. We don't have an SAE connector…
view full answer...We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based…
view full answer...Thanks for the picture of what you have and the info you listed. The correct wheel you need is the part #AM20794 that you referenced.
view full answer...We do offer the Trailer Connector Adapter, #HM47425, which converts a 7-pole round connector to a 7-pole flat connector. This adapter works for tow vehicles with combined taillight wiring, meaning that the turn signals and brake lights run on the…
view full answer...You would not be able to charge your battery through the wiring on your 4-way trailer connector. Since your truck has a 7-way connector, you could maintain the power to the battery but not charge it. To begin, you would need to cut off your 4-way…
view full answer...