Bunk board not sitting flush against your hull? This EZ Loader bent plate bunkmountingbracket attaches bunks to upright brackets and allows proper angling for better hull contact. ... Highlights Fixes Poor Bunk Angle Contact: Adjusts bunk position so it sits flush with the hull. MountsBunks to Upright Brackets: Connects bunk boards securely to vertical supports.
Thin van walls can make it difficult to install an awning window without adding spacer material behind the frame. This bracket adds the support needed so the Overlander OVR-AW4015 window can tighten securely against van walls up to 1/8" thick.Highlights Supports Thin Wall Installs: Allows mounting on van walls up to 1/8" thick. Adds Backing For The Frame: Provides support behind the inner frame during installation. Replaces Spacer Material: Avoids stacking wood or filler pieces behind the window.
Loose or shifting bunk boards can affect how your boat sits on the trailer. This EZ Loader galvanized 11-gauge bunkmountingbracket secures the bottom of your bunk boards to support brackets. ... Highlights Stops Bunk Boards From Shifting: Secures boards to support brackets so they stay in place. Maintains Proper Boat Support: Keeps bunks aligned for consistent hull positioning. 11-Gauge Steel Construction: Provides thickness needed for trailer bunkmounting.
Thin van walls can make it difficult to install an awning window without adding spacer material behind the frame. This bracket adds the support needed so the Overlander OVR-AW3515 window can tighten securely against van walls up to 1/8" thick.Highlights Supports Thin Wall Installs: Allows mounting on van walls up to 1/8" thick. Adds Backing For The Frame: Provides support behind the inner frame during installation. Replaces Spacer Material: Helps avoid stacking wood or filler pieces behind the window.
Worn or damaged bunkbracket causing loose boards on your personal watercraft trailer? This galvanized EZ Loader pork chop strap bunkmountingbracket restores secure bunk support on compatible personal watercraft trailers.Highlights Restores Secure BunkMounting: Replaces a worn bracket so bunk boards stay firmly attached during loading. Keeps Boards From Shifting: Holds bunk boards in position to maintain proper support on the trailer.
These carpeted bunk boards replace your boat trailer's worn-out bunk boards. Each 7' long 2x4 is covered with durable, marine-grade carpet that helps protect the finish on your boat's hull and is easy to clean.Each 7' long board is wrapped in weather-resistant, marine-grade black carpet. You can run the bunk boards front to back for traditionally shaped hulls or side to side for flat-bottom boats, kayaks and inflatables. To attach the bunk boards to the front and rear crossmembers of your trailer frame, use existing brackets or a four-pack of swivel mountingbrackets (CE10000G-4, CE10001G-4 or CE10002G-4 - sold separately).
These carpeted bunk boards replace your boat trailer's worn-out bunk boards. Each 6-foot-long 2x4 is covered with durable, marine-grade carpet that helps protect the finish on your boat's hull and is easy to clean.Each 6-foot-long board is wrapped in weather-resistant, marine-grade black carpet. You can run the bunk boards front to back for traditionally shaped hulls or side to side for flat-bottom boats, kayaks and inflatables. To attach the bunk boards to the front and rear crossmembers of your trailer frame, use existing brackets or a four-pack of swivel mountingbrackets (CE10000G-4, CE10001G-4 or C10002G-4 - sold separately).
Rust-resistant assemblies let you install 2 bunk boards on your boat trailer. Swivel brackets enable bunks to tilt when loading a boat. Mounting slots allow for height adjustment. ... Features: Bolster-and-swivel bracket assemblies allow you to install 2 bunk boards on your boat trailer Dimpled bolster bracket surfaces help prevent the brackets from sliding along the trailer frame Mounting slots permit as much as 3-3/4" of height adjustment during installation Each bolster bracket installs vertically on your boat trailer's frame with a U-bolt (sold separately) Strong swivel brackets let you tilt the bunk boards Helps you to fit the boat hull snugly onto trailer during the loading process Hardware is included for attaching the swivel brackets to the bolster brackets 11-Gauge, galvanized steel resists rust and corrosion Suitable for saltwater exposure Made in the USA Specs: Quantity: 4 bracket assemblies Overall height: 9" Dimensions of bolster bracket: 8" tall x 2-1/2" wide Mounting slot dimensions: 2-3/4" long x 1/2" wide Spacing between mounting slots: 1/2" Dimensions of swivel bracket: 3-1/2" long x 1-3/8" wide x 2" tall Flange mounting hole diameters: 3/8" Flange mounting hole spacing: 2-1/2" apart on center Bolster-and-swivel-bracket assemblies are typically mounted upright on a boat trailer's crossmembers.
... Attach directly to bunk boards or use mountingbrackets (sold separately).If you want to replace your bunk boards and attach the roller bunks to the front and rear crossmembers of your trailer frame, use a four-pack of swivel mountingbrackets (CE10003G-4 - sold separately).
Carpeted bunks wear out and drag against your hull. Amber polyvinyl rollers trade that drag for a smooth, easy glide, even in shallow water. Made to last a lifetime, they resist sun and water without marking your boat.Made to Last: Galvanized steel resists rust and corrosion. Flexible Mounting: Choose the hardware and brackets (sold separately) that fit your trailer. Features to know about Smooth Rolling Instead of Dragging Would you rather push a box across the floor or move it with a dolly?
Rust-resistant assemblies let you install 2 bunk boards on your boat trailer. Swivel brackets enable bunks to tilt when loading a boat. Mounting slots allow for height adjustment. ... Features: Bolster-and-swivel bracket assemblies allow you to install 2 bunk boards on your boat trailer Dimpled bolster bracket surfaces help prevent the brackets from sliding along the trailer frame Mounting slots permit as much as 3-3/4" of height adjustment during installation Each bolster bracket installs on your boat trailer's frame with a U-bolt (sold separately) Strong swivel brackets let you tilt the bunk boards Helps you to fit the boat hull snugly onto trailer during the loading process Hardware is included for attaching the swivel brackets to the bolster brackets 11-Gauge, galvanized steel resists rust and corrosion Suitable for saltwater exposure Made in the USA Specs: Quantity: 4 bracket assemblies Overall height: 13" Dimensions of bolster bracket: 12" tall x 2-1/2" wide Mounting slot dimensions: 4-3/4" long x 1/2" wide Spacing between mounting slots: 1/2" Dimensions of swivel bracket: 3-1/2" long x 1-3/8" wide x 2" tall Flange mounting hole diameters: 3/8" Flange mounting hole spacing: 2-1/2" apart on center Bolster-and-swivel-bracket assemblies are typically mounted upright on a boat trailer's crossmembers.
These carpeted bunk boards replace your boat trailer's worn-out bunk boards. Each 5-foot-long 2x4 is covered with durable, marine-grade carpet that helps protect the finish on your boat's hull and is easy to clean.Each 5-foot-long board is wrapped in weather-resistant, marine-grade black carpet. You can run the bunk boards front to back for traditionally shaped hulls or side to side for flat-bottom boats, kayaks and inflatables. To attach the bunk boards to the front and rear crossmembers of your trailer frame, use existing brackets or a four-pack of swivel mountingbrackets (CE10000G-4, CE10001G-4 or C10002G-4 - sold separately).
Rust-resistant assemblies let you install 2 bunk boards on your boat trailer. Each assembly attaches to the trailer frame with 2 U-bolts (sold separately) for a sturdy connection. Swivel brackets enable bunks to tilt when loading a boat.Features: Bolster-and-swivel-bracket assemblies allow you to install 2 bunk boards on your boat trailer Extra-sturdy connection to trailer frame ensures support for the bunk boards Each bolster bracket attaches with 2 U-bolts (sold separately), as opposed to a standard bracket that attaches with 1 U-bolt Mounting slots permit as much as 3" of height adjustment during installation Bolster brackets install vertically on your boat trailer's frame Heavy-duty swivel brackets let you tilt the bunk boards Helps you to fit the boat hull snugly onto your trailer during the loading process Hardware is included for attaching the swivel brackets to the bolster brackets 3 Bolt holes for a strong, sturdy connection to the bunk board 7-Gauge, galvanized steel resists rust and corrosion Suitable for saltwater exposure Made in the USA Specs: Quantity: 4 bracket assemblies Overall height: 16-1/4" Dimensions of bolster bracket: 15" tall x 4" wide Mounting slot dimensions: 3" long x 1/2" wide Horizontal spacing between slots: 1-3/4" Dimensions of swivel bracket: 3-1/2" long x 1-1/2" wide x 2" tall Flange mounting hole diameters: 3/8" Flange mounting hole spacing: 2-1/2" apart on center 1-1/4" Between each of the 3 holes Bolster-and-swivel-bracket assemblies are typically mounted upright on a boat trailer's crossmembers.
Rust-resistant assemblies let you install 2 roller bunks on your boat trailer. Swivel brackets enable bunks to tilt when loading a boat. Mounting slots allow for height adjustment. Dimpled surfaces keep brackets from sliding along the trailer frame.Features: Bolster-and-swivel bracket assemblies allows you to install 2 roller bunks on your boat trailer Dimpled bolster bracket surfaces help prevent the brackets from sliding along the trailer frame Mounting slots permit as much as 3-3/4" of height adjustment during installation Each bolster bracket installs on your boat trailer's frame with a single U-bolt (sold separately) Strong swivel brackets let you tilt the roller bunks Helps you to fit the boat hull snugly onto trailer during the loading process Hardware is included for attaching the swivel brackets to the bolster brackets 11-Gauge, galvanized steel resists rust and corrosion Suitable for saltwater exposure Made in the USA Specs: Quantity: 4 bracket assemblies Overall height: 11" Dimensions of bolster bracket: 10" tall x 2-1/2" wide Mounting slot dimensions: 3-3/4" long x 1/2" wide Spacing between mounting slots: 1/2" Dimensions of swivel bracket: 1-1/4" long x 1-3/4" wide x 2" tall Top flange mounting hole diameter: 7/16" Bolster-and-swivel-bracket assemblies are typically mounted upright on a boat trailer's crossmembers.
Steep ramps can make launches tricky. Black rubber rollers strike the balance between smooth rolling and added grip, so your boat loads with control and stays put until youre ready to push off.Made to Last: Galvanized steel resists rust and corrosion. Flexible Mounting: Choose the hardware and brackets (sold separately) that fit your trailer. Features to know about Smooth Rolling Instead of Dragging Would you rather push a box across the floor or move it with a dolly?
Rust-resistant assemblies let you install 2 bunk boards on your boat trailer. Each assembly attaches to the trailer frame with 2 U-bolts (sold separately) for a sturdy connection. Swivel brackets enable bunks to tilt when loading a boat.Features: Bolster-and-swivel-bracket assemblies allow you to install 2 bunk boards on your boat trailer Extra-sturdy connection to trailer frame ensures support for the bunk boards Each bolster bracket attaches with 2 U-bolts (sold separately), as opposed to a standard bracket that attaches with 1 U-bolt Mounting slots permit as much as 3" of height adjustment during installation Bolster brackets install vertically on your boat trailer's frame Heavy-duty swivel brackets let you tilt the bunk boards Helps you to fit the boat hull snugly onto your trailer during the loading process Hardware is included for attaching the swivel brackets to the bolster brackets 3 Bolt holes for a strong, sturdy connection to the bunk board 7-Gauge, galvanized steel resists rust and corrosion Suitable for saltwater exposure Made in the USA Specs: Quantity: 4 bracket assemblies Overall height: 12-1/4" Dimensions of bolster bracket: 11-3/4" tall x 4" wide Mounting slot dimensions: 3" long x 1/2" wide Horizontal spacing between slots: 1-1/4" Horizontal spacing between slots: 1/2" Dimensions of swivel bracket: 3-1/2" long x 1-1/2" wide x 2" tall Flange mounting hole diameters: 3/8" Flange mounting hole spacing: 2-1/2" apart on center 1-1/4" Between each of the 3 holes Bolster-and-swivel-bracket assemblies are typically mounted upright on a boat trailer's crossmembers.
These sturdy square U-bolts let you secure 2 double U-bolt bolster brackets or 4 standard bolster or bunk board brackets to your boat trailer's frame. Galvanized steel is durable and corrosion resistant. Hardware included.Features: 4 Heavy-duty square U-bolts let you secure brackets on your boat trailer Works with 2 double U-bolt bolster brackets or 4 standard bolster or bunk board brackets Designed for use with brackets that have 1/2" diameter mounting holes or 1/2" wide mounting slots Galvanized steel resists rust and corrosion Suitable for saltwater exposure Includes mounting hardware Made in the USA Specs: Quantity: 4 U-bolts Inner width: 3-1/16" Length: 3-13/16" Bolt size: 1/2"-13 Thread length: 1-1/2" Overall length: 4-5/16" Galvanized Steel Galvanized steel parts are hot-dipped in zinc after being stamped.
These carpeted bunk boards replace your boat trailer's worn-out bunk boards. Each 3-foot-long 2x4 is covered with durable, marine-grade carpet that helps protect the finish on your boat's hull and is easy to clean.Each 3-foot-long board is wrapped in weather-resistant, marine-grade black carpet. You can run the bunk boards front to back for traditionally shaped hulls or side to side for flat-bottom boats, kayaks and inflatables. To attach the bunk boards to the front and rear crossmembers of your trailer frame, use existing brackets or a four-pack of swivel mountingbrackets (CE10000G-4, CE10001G-4 or C10002G-4 - sold separately).
Bunk-board kit lets you build your own guide-ons to ease loading of your boat onto your trailer. Kit includes 90-degree-angled tubes, brackets, hardware, and enough marine-grade carpet for (2) 69" long 2x4 boards (not included).Features: Bunk-board kit lets you create 2 guide-ons to support your boat and keep it centered while you're loading it onto your trailer 2x4 Lumber for bunk boards not included 90-Degree-angled tubes let you mount the bunks close to your boat Great for narrow boats Bolt-on installation - clamp onto top or bottom of your trailer's frame Pre-galvanized steel construction is sturdy and corrosion-resistant Marine-grade carpeting lines bunk boards to protect your boat's finish 2 Rolls included to cover 2 boards U-bolts, brackets, and mounting hardware included Made in the USA Specs: Application: trailer frames up to 3" wide x 4-1/2" tall 2 Extra-long U-bolt kits (CE11416 - sold separately) are required to mount on frames up to 3" wide x 5-1/4" tall 2 Sets of I-beam clamps (CE27682A - sold separately) can be used to mount on I-beam frames that are larger than 3" wide x 4-1/4" tall Carpeting dimensions (per roll): 11" wide x 12' long Maximum 2x4 length for carpeting: 69" Pre-Galvanized Steel Pre-galvanized steel parts are stamped from a sheet of steel after it has already been galvanized.
Mount your boat trailer's bunk board using this rust-resistant bolster bracket, which helps support your bunk when used with a swivel bracket (sold separately). ... Features: Bolster bracket lets you attach a swivel bracket (sold separately) for mounting a bunk board to your boat trailer 2 Brackets are required to mount 1 bunk board (additional bracket sold separately) Dimpled surface helps prevent the bracket from sliding along your trailer's frame Mounting slot lets you adjust the bracket's height during installation Bracket installs vertically on your boat trailer's frame 11-Gauge, zinc-plated steel resists rust and corrosion Made in the USA Specs: Quantity: 1 bracket Dimensions: 10-1/8" tall x 2-1/2" wide x 1" deep
This awning bunk window is for camper vans where you want airflow, shade, and privacy in one opening. Instead of adding separate screens and blackout panels, it combines a two-stage awning vent with an integrated mesh screen and pleated shade.It also blocks 83% of UV rays, reducing sun exposure through that section of glass. Clamp Ring Mount And Wall Fitment The clamp ring sandwiches the van wall between the interior and exterior frame to secure the window. Installation requires spacer material between the wall and clamp ring unless using mountingbracket (VW67FR - sold separately) for walls up to 1/8" thick, so the window installs with consistent support instead of relying on stacked spacers.
Rub marks, squeaks, or crooked loading? A swivel bolster lets you pivot your bunk so it sits flush to your hull. You set the height, it spreads the boat's contact, and you'll load your boat smoother while protecting it's finish.Ready to Install: Includes mounting hardware for a straightforward setup. Features to know about Centered, Scuff-Free Loading When a boat loads crooked or rubs the same spot every trip, it's usually a bunk alignment issue, not the hull.
Easily load your pontoon boat with these bunk-board-style guide-ons. The boards are covered with marine-grade carpet and their height can be adjusted during installation. Fits trailer frames up to 3" wide x 4-1/4" tall. Hardware included.The galvanized steel support posts mount on top of the crossmember on your pontoon boat trailer's frame. Just slide the posts into the mountingbrackets and secure the posts so that the distance between each bunk and pontoon is approximately 2" to 3".
Heavy-duty, rust-resistant brackets let you mount extra-large bunk boards on their sides to hold large boats. The included 85-degree and 95-degree brackets install on an angled or V-shaped boat trailer frame with 2 U-bolts (sold separately).Features: Heavy-duty brackets let you mount a bunk board on your boat trailer Ideal for big bunk boards, such as 3x8 or 4x8 Stabilizes one end of the bunk board - additional brackets (sold separately) required for opposite end of board 85-Degree and 95-degree angles are designed for vertical mounting onto angled or V-shaped boat trailer frames Ensures alignment of the bunk board mounting holes Requires (2) 1/2" diameter U-bolts (sold separately) for installation 3 Pre-drilled holes on each bracket let you raise or lower the bunk board during installation Secure board vertically on its side between the brackets with a 1/2" bolt (sold separately) Galvanized steel resists rust and corrosion Suitable for saltwater exposure Made in the USA Specs: Quantity: 2 brackets Overall dimensions: 85-Degree bracket dimensions: 6" tall x 5" wide 95-Degree bracket dimensions: 7" tall x 5" wide Distance between trailer mounting holes (center to center): 3-9/16" Distance between bunk board mounting holes (center to center): 1-1/16" Plate thickness: 1/4" Galvanized Steel Galvanized steel parts are hot-dipped in zinc after being stamped.
Filters
