Result: socket

Is the socket required for an A194B bulb the same as an international standard T10 socket? | Is the socket required for an A194B bulb the same as an international standard T10 socket? | I spoke with my contact...

what size socket do you need to tighten the nuts and does a short socket work or do you need a deep socket? | what size socket do you need to tighten the nuts and does a short socket work or...

Can this socket be used to tighten the ball to the hitch blue ox sway pro or are the walls of the socket too thick? | Can this socket be used to tighten the ball to the hitch blue ox sway pro or are the walls...

To adjust the hitch ball in your weight distribution system, what you will need is a socket and torque wrench; for the socket you will need the following: - 1-7/8" 12pt Thin Walled Socket - 3/4" Drive # ALL643216 This will require a torque/socket wrench with a 3/4" drive; I have added a link below to a video showing exactly how the socket works for a weight distribution system. |

Plastic Stem and Rubber Socket Door Holder - 2inch Long Stem Item # DH39R What is the diameterinch of the socket? | Plastic Stem and Rubber Socket Door Holder - 2inch Long Stem Item # DH39R What is the diameterinch...

At my job, alot of techs get sockets that dont fit around the nut on the ball. | At my job, alot of techs get sockets that dont fit around the nut on the ball. This is due to the round sockets on the hitch head, that are for...

I would like to install etrack with these wood end beam sockets to use as shelf boards. I am concerned that if I don’t screw the 2x4 into the sockets, the board could potentially jump out of the socket or at least bounce/shake more than I like if lightly loaded….but I would also like to be able to remove the board/socket when not in use. |

We carry two different plunger sockets that could potentially work for you. The Nylon Replacement Socket part # DH600S and the Replacement Rubber Socket # DH38S. | Does etrailer sell on the...

How does the nylon socket attach? | How does the nylon socket attach? | The white socket of the Plunger and Socket Door Holder part # DH604 that you referenced attaches with a bolt that runs through the center of it. I attached...

Will this socket work to install the ball on an Equalizer hitch head? | Will this socket work to install the ball on an Equalizer hitch head? I know it needs to be a thin walled socket. | The Powerbuilt 1-7/8 Inch 12pt Socket...

Here is a list of the different bulb and socket kits we currently offer. Roadmaster Tail Light Wiring Kit with Bulbs # RM-155 Blue Ox Tail Light Wiring Kit - Bulb and Socket # BX8869 Roadmaster Tail Light Wiring Kit w/ 7-Way to 6-Wire Connector - LED Bulb and Socket - Red # RM-152-LED-7 Roadmaster Tail Light Wiring Kit for Towed Vehicles - LED Bulb and Socket - Red # RM-152-LED Blue Ox Tail Light Wiring Kit for Towed Vehicles - Integrated LED Bulb and Socket - White # BX88269 Blue Ox Tail Light Wiring Kit for Towed Vehicles - Integrated LED Bulb and Socket - Red # BX88267 If you already have the bulb and sockets and only need the wiring we do have the 4-Way Wiring # 16-4B-1 sold by the foot. |

Looking to replace three nylon door sockets for down windows on a horse trailer. Appears present item on trailer is DH605. | Looking to replace three nylon door sockets for down windows on a horse trailer. Appears present...

So id like to know if the socket can hold the stem even if there is an angle between the stem and the socket thank you | Hello, im looking to use the plastic 2 in. stem with the rubber socket door holder on...

The jack crank handle is imminently breaking. It has a 3/4inch socket. Would your JCH-1 work with this? Does it have a tiny Phillips screw in the socket area? | Hi i have a 2013 R Pod 177 trailerForest River...

This socket will plug into the OEM female end socket on the vehicle. | Is this item compatible with the 2007 Toyota Tundra OEM hitch 7 and 4 pole connector unit? | The Pollak 7 and 4-Pole Trailer Connector...

Do you carry any plunger and socket in a stainless steel? The zinc coated didnt last the winter salt | Do you carry any plunger and socket in a stainless steel? The zinc coated didnt last the winter salt | Every steel socket...

What size socket does the WM9062 require? | What size socket does the WM9062 require? | The Replacement 22 mm Lug Nut for Wheel Master Wheel Liner # WM9062 is a 22mm nut, so you'll need a metric socket set with a 22mm socket....

Does this nut take a 13/16inch socket? I need a chrome nut that is 1/2-20 thread that takes a 13/16inch socket to intall. | Does this nut take a 13/16inch socket? I need a chrome nut that is 1/2-20 thread...

I will need an adapter because I dont have a 3/4inch socket. Will the digital torque adapter work even if I put a socket size adapter on my socket wrench? | I am getting the 1-7/8inch 12pt...

Can this socket be used with an air impact wrench? | Can this socket be used with an air impact wrench? | Thanks for checking in with us, Ian! The 1-7/8" 12pt Thin Walled Socket # ALL643216 is intended for use with a standard...

Or will a standard 1 7/8inch socket work | Is your thin wall socket eq70-00-4800 required for torquing the nut on the Reese steady flex 66560? Or will a standard 1 7/8inch socket work | The thin walled socket is needed for the...

In my opinion, I would replace both the plunger and the socket to ensure that they are a good fit. - Plunger and Nylon Socket Door Holder # DH604 (1" long plunger) - Plunger and Nylon Socket Door Holder # DH605 (2" long plunger) - Pivoting Plunger and Socket Door Holder # 37210645 (3" long pivoting plunger) |

I currently have a 7- and 4-Pole Trailer Connector Socket w/ Mounting Bracket Item # HM40975. What I need are the retention clips that hold the socket to the bracket. | I currently have a 7- and 4-Pole Trailer...

The pin assembly on the Pollak 6-Pole Socket # PK11609 will push out the front of the socket. | Is the pin assembly of the 6-pin socket pushed out of the front or pulled out of the rear? I want to add a wire....