Result:

I have a ‘56 airstream. My question is the trailer brake wiring. Do you recommend grounding each magnet wire at the axle area, or running a separate ground wire , along with the blue wire, up to the 7 point connector and tapping into the ground...

I am looking to upgrade the rear lights of my Car Mate 5x8foot utility trailer. I currently have Peterson PM444L lights. I am hoping to use the TLL16RK set however I am not sure if they will fit. The Petersons have the standard 2 inch center...

HADCO brake drums. I’m converting my ‘56 Bubble airstream to electric brakes. I installed the new backing plates with magnets, shoes etc. Can I use my original brake drums/ hubs, or do I need a special backing plate to bolt on the inside? It...

Is there anything special about manually adjusting self adjusting trailer brakes? I notice there are 2 little openings in rear of backing plate. One has the wheel. What’s the other opening for? Do I have to move the self adjuster out of the...

I’m installing a Curt echo wireless brake controller on my ford ranger. I do not have a 12 vol power wire currently connected to my 7 pain truck re eptacle. The trailer brakes on on a 10 gauge wire T terminating at the trailer 7 point plug. Question:...

I have a continuous 10gauge wire between the wheels with electric brakes. I want to tap into that wire and run a single 10 gauge wire to my 7 blade trailer side connector. Ground wires are grounded to frame at the wheels. Question: what’s the...

I have a C.R. 18823 grease seal on my 1956 airstream bubble trailer. It’s 3” OD. Do you have anything comparable? Thanks | Hey Larry, yes we do have a grease seal replacement for what you have with the part # 29031. This has the outer diameter...

I have a 1956 airstream Bubble. It had hydraulic brakes- totallly non functional. Brakes are 12” and 2” wide. My question is can I use my 12” hubs with the new loaded backing plates, or do I need new hubs as well. They are in fine condition. Thanks, Larry...

I bought a curt triflex for my new trailer about 3 months ago. The brake controller worked flawlessly up until about a week ago. One day the controller gave me an ol code. I hooked the trailer up to my buddies truck and no code and the brakes...

Can you put a ball on the rear of a receiver hitch cargo carrier to pull a light trailer? | We do have an easy solution for you to use a cargo carrier and tow at the same time, though you would not be able to put a hitch ball on a cargo carrier...

Will this fit a SAE AP2 01 replacement amber side maker lens for a 2007 Rockwood Freedom 1640 LTD tent trailer? | If your original light is 4" L x 2" W x 1-1/8" D then Optronics light # MC32AB will fit in its place. If you have different dimensions...

HAVE SIGNAL BRAKE FLASHERS BUT NO TAIL LIGHTS HAVE NO POWER AT THE PLUG CANT FIND A BLOWN FUSE HELP | Since you have brake and turn but not taillights, the issue can be a fuse, a relay, bad wiring, or a weak connection. I recommend you first...

Does this with mounting brackets? | Hello Raymond, thanks for reaching out. The mounting brackets are not included with the GE Appliances RV Refrigerator # GE58FR. It requires a GE approved top bracket part BMT-GPV10. This is not something we...

I have been getting mixed information about using my Ranger as a flat tow vehicle. The owners manual says I can use it as a dinghy. It is a 2WD 5speed. Is this a vehicle I can tow, and what parts do I need to order? It is the sport model....

I have a 2007 Ford Ranger sport with the step bumper designed for towing from factory. It has the holes for the breakaway chains for towing and a large lip at the front. The ball is right in the middle in a factory hole. I measured from the...

I have a 2007 ford ranger and I am gonna install the Curt 55515 trailer connector does the ecu need to be flashed? | Installing the Curt T-Connector Vehicle Wiring Harness item # C55515 will not require you to flash the ecu on your 2007 Ford...

What is meant by stabilizing straps for non-trailer loads? | Non-trailer loads are hitch accessories like bike racks and cargo carriers. Basically anything that is not a trailer that you could put on a hitch. Curt recommends you use a Curt Trailer...

For the hitch Item # C12012 is there drilling required for installing on my 07 ranger? Will this hitch Item # C12012 fit with a full size spare tire? | Drilling is required to install Curt Class II trailer hitch # C12012 on your 2007 Ford Ranger....

I have a 2007 Ford Ranger with a 4 pin for my trailer lights. However, I just got a tear trailer and it comes with a round, 7 pin female end. What part do I need? Thank you | If the trailer you are towing has brakes you will need a brake...

Will I need to drill holes in some part of the car to install the hitch ? | There is no drilling required to install the Curt hitch part # C11094 on your 2007 Kia Rio. Basically you will just raise the hitch into position and then bolt it into...

Can a 2007 Ford Ranger XLT 4.0 2WD be flat tow ? If so whats needed? | According to the owners manual for your 2007 Ford Ranger XLT 4.0 2 wheel drive you can flat tow your Ranger. If you have a manual transmission you are able to tow an unlimited...

IM DISABLED I CANT LIFT MY LEG UP HIGH. IM INTERESTED IN THE KWIKEE 28. WHATS THE PROBLEM WITH THE MOTOR NOT SHUTTING OFF? IS THERE A WIRE HARNESS LONG ENOUGH TO REACH MY BATTERY DO I NEED ANYTHING ELSE TO MOUNT IT ON MY TRUCK? WHEN CLOSED,...

will this part work for my 2007 ford ranger? I want to be able to rent a trailer requiring a 4 way flat end for the trailer side. is there a plug in trailer wiring harness that would not require any splicing? any suggestions, details appreciated. thanks...

Is this weight distributing for the Ranger? I would prefer a weight distributing hitch the best I can put on. What do you recommend? Also there is a capped plug that seems to be from the factory. Is there something I need to plug into that...