Result: knobs

The knobs themselves are 2-1/4" in diameter and 1-1/2" tall. | how many inches are between the ladder rack knobs that screw into the deck rail. I want to know if my tool box can fit in between the rack when installed in a tundra...

Im looking for replacement knobs for a Rola Haul your might truck rack. Also wondering if knobs from another brand of rack might work. | Im looking for replacement knobs for a Rola Haul your might truck rack....

The box can then be placed as far forward in the truck bed which will butt it up against the forward-most ladder rack knobs. You could then have the bolt that the second set of knobs uses go through the sides of the box and thread on the knob from the inside of the box to hold the toolbox in place though this may require a longer bolt. |

Be sure to determine a location on the dash where you will be mounting the actual controller knob so the cable from the control knob can reach the control module mounting location under the dash. | Thanks...

The Rola rack uses four locking knobs on each upright to secure itself inside the rails on your truck. | does the sliding tracrack fit a 2017 tacoma ?does the rear rack slide forward? | I do have options for you but they do...

The main unit mounts out of site so only the control knob is visible in the cab. The knob controls the braking power and also acts as the manual override. | Do you have a 7 pin flat trailer wire harness for...

But after I dialed up the power knob to greater than minimum, the unit read flashing n.c. | I had trouble pairing the Prodigy RF. After going through all the steps, the readout on the remote unit never was 0.0 and continued...

To correct this, rotate the level knob counter-clockwise, away from you. Repeat these steps until your desired braking is achieved. | i am just wondering why i would need to replace the stock 7-Way Connector to a new one. i...

If you have one of those empty spots in the dash, you can use a Universal Mounting Panel for Redarc Tow-Pro Trailer Brake Controller Control Knob # 331-TPSI-001 to install the knob. *Since your vehicle does not have the factory tow package you will need to splice in the brake controller. |

This will provide you with a sleek proportional brake controller knob that doesn't need a bulky controller in your Crosstrek. | Hi, I need a 7 pin wiring harness, brake controller, and bracket ? to plug the trailer into for...

The Tow-Pro Elite brake controller is pretty unique because it can be installed virtually anywhere and you only need access to the 3/4" diameter control knob. The control knob has LED lighting integrated into it that changes colors depending on what settings you have chosen. |

It is a small knob that does not take up much room with the bulk of the controller mounted behind the dash. | I'm getting ready to install your receiver # e83ZR on my 2022 Subaru Forester for pulling my camping trailer. This...

This would allow you to use a trailer brake controller like the Redarc Tow-Pro Liberty Brake Controller # RED24FR, which is going to have a sleek control knob instead of a big bulky controller. You will need the Universal Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers # RED69FR for installation and can use the Universal Mounting Panel for Redarc Tow-Pro Trailer Brake Controller Control Knob # 331-TPSI-001 to provide a more factory like appearance. |

The trailer brakes are adjusted using the control knob which can be mounted within reach of the driver. | I need a complete towing package for my 2022 Toyota Highlander, hitch, wiring and brake controller. What parts are needed?...

I have tried the suggestion to have the power knob set higher than minimum step 6 but still n.c. flashing even after re-connecting the trailer to the power module. | I have a 2017 Volvo XC 90 with tow bar and wiring done by...

The base of the rack could be left on if you wanted to unbolt them from the feet but realistically it would be easier to just remove the feet all together since they install with knobs that don't require tools. | Ill be using...

You'll control the trailer brakes via a knob that can be mounted anywhere within the drivers reach. | I need a wire harness for my 2016 Honda Pilot , Must be a 7 pin and have the ability to add a break controller later on if...

As the factory bed length on your truck is 62", I recommend placing the ladder racks 50" or so apart from one another. The knobs located on the brackets inside the bed rail will loosen to reposition the racks then tighten back down once you have them in their desired location. |

Once the Rola Haul-Your-Might T3 Truck Bed Ladder Rack # 59799 is installed in the bed of your Toyota Tundra it will be easy to remove by loosening the the 8 knobs, and sliding the racks out of your deck rail system. | I’m...

This unit is proportional and the main component is hidden behind your dash. The control knob can be mounted directly to the dash or with the Universal Mounting Panel # 331-TPSI-001 for a more factory appearance. | Greetings!...

It will also come with come with sliding load stops that can easily be loosened by turning the hand knobs and slid around to fit your needs. I've attached a short review video below that will let you get a better look at this ladder rack and decide if this will meet your needs. |

When you want to remove it, you can leave the base on and detach the rest, but it might be easier for you to remove the whole rack by loosening the knobs and sliding it out of the bed rails. The rack weighs 43.7 pounds, so the ease of removal really depends on if you're comfortable handling that amount of weight. |

Otherwise, if you're needing to ADD 4-Way and 7-Way sockets then you need the following parts: - Curt T-Connector Vehicle Wiring Harness # C58DR - Universal Installation Kit # ETBC7 - No-Drill Mount Bracket, Long # 18136 - Extra 10 Gauge Wire # 10-1-1 (on an as-needed basis) If you also need a brake controller then I really like the Redarc Tow-Pro Liberty Brake Controller w/ Universal Wiring Harness # RED52VR because it can be installed virtually anywhere and the control knob doesn't take up much space. This will splice in to the wiring you ran for the ETBC7. |

This controller has a small control knob which will mount to your dash and the main body of the unit will be hidden behind the dash for a clean look. | LOOKING TO INSTALL A TOW BAR ON A 2023 JEEP WRANGER SAHARA AND WAS LOOKING...