!Stampede Travel Trailer  x   >   !1988  x   >   !veloster  x   >   TRC  x   >  

Can this spring be used for a 150# roll up box truck door? The picture looks like it has everything I need, and the rod length/door weight/cable lengths are compatible, but all the setups Im seeing on eTrailer state that these are ramp door...

Can the gorilla lift be installed on an enclosed trailer? | I have a solution for you but the Gorilla Lift item # GL1 you referenced only works on utility trailers with raised bed rails. To help raise the ramp door of an enclosed trailer you...

Do you have a practical example of the J-channel trim on a trailer? Could it be used as bottom rail with siding nesting in channel? If so is there enough space to overlap .040 sheets? How wide is channel? | I spoke to TRC and the gap/channel...

Does this unit have a constant 120 lb pull over the full range of travel? Im looking at a 71inch pull to fully close my ramp application attaching to the ramp at the folding hinge point shown in this picture and was wondering what the force...

Whats the pin diameter? | The pin diameter of the 2" Wide Continuous Hinge # 362TRCPH2 that you referenced is 1/4 inch. |

What are the measurements and specs on part 362SA8207? | The Conventional Ramp Door Spring for 8' Wide Enclosed Trailer # 362SA8207 is 96" wide, 4-7/8" tall and 7-1/2" deep when mounted above the trailer door. The entire assembly weighs 30lbs...

Hello I am looking for the H Channel for our enclosed trailer. The door on the used trailer is a mess and wed like to replace it. Do you have a Canadian distributor for you your parts? the video i watched on your website shows exactly...

I need to build 4 exterior side entry cargo trailer doors. They are made with aluminum “h” channel. Do you have any channel specific to this purpose? Thanks | Yes, we do have some "H" channel that is designed to be used for enclosed trailer...

Do l have to buy a full length of uneven rub rail if l need 70in? Says you can cut it. | The # 36284-955 Rub Rail is only available in the 93-1/2 inch length, it can be cut to size as needed but we only sell the full length. |

I see that you have Torsion spring kits for 80 lb and 120 lbs doors. My door is 95 lbs. Which kit do I choose? Will the 120 lb spring have a tendency to lift the door when fully open or be will it be harder to operate and pull open? Will...

I am looking at converting a small enclosed trailer which currently has a swing door to a ramp door to make it easier to load my motorcycle. I know I will have to beef up the inside of the door for the increased weight. The door is 48inch wide....

Does this seal come in 5/8-inch width? I found this 3/4-inch which I need and the 1/2-inch, but havent found it in 5/8-inch width. Thank you! | The D-Shaped Rubber Seal is not available in 5/8 inch width just the 3/4 inch # 362WS1048-25 and...

I have a 2021 Forest river salem 263bhxl that has the full length gutter drip rail that runs the length of the trailer. How do I slide the new slide topper down the rail ? | The Solera # LCV000163285 attaches to the sidewall of your trailer...

need trim around inside inter door that glues on between wall screendoor for seal. | You could use the D-Shaped Rubber Seal for Enclosed Trailer # 362WS1463-25 as a seal for your RV screen door. This is a 25 foot roll that is 1/2 inch tall and...

Where do I measure the width of trailer ramp door? Inside, outside or opening on trailer? | You will want to measure the width of available headroom inside of the trailer. So above the door opening, left to right walls, from the inside. The...

Hi can this be cut to size my old measures 62inch end to end. Thanks | I spoke with my contact at TRC and he assured me that the Trailer Ramp Spring, part # 362SW61, can be cut down to the 62 inches you want. He also stated that these items...

slide out is 179". need white awning tia | For your application you need the Solera RV Slide-Out Awning # LCV000163304 which fits slide-outs 176" - 181" wide so it will work great for your 179" wide slide out. This kit comes with everything...

Can this be bent to go on a Canned Ham Shape Camper - If not which do you recommend | Personally, I recommended the J-Channel Trim for Enclosed Trailer # 362415-955 which is made of a soft metal that will allow you to bend the metal to the shape...

What sealant should be used underneath the flange when installing? Should Dicor be used or Butyl tape? | When installing the MaxxFan Deluxe Roof Vent w/ 12V Fan, Thermostat, and Remote # MA00-07500K you will want to use both the Butyl Tape...

I have a fleetwood pegasus 190xp hybrid trailer , I am looking for the bed bunk door seals | We have weatherstripping tape that can be used to seal your bed bunk doors withe part # WS1434 which is 3/4 inch wide that is 50 foot long or the part...

Is this soft j-rail and easily formable | The J-Channel Trim for Enclosed Trailer part # 362415-955 is made of aluminium which is a very soft metal so yes it could be bent or conformed to a certain shape if needed. However, if you need to make...

Do you have a gas or spring loaded hinge that would make it easier to lift a basement door that has bee built in the floor. It could weigh between 50-75+ pounds and is impossible for a normal woman or man to lift. | You could use a trailer...

Hi, Looking at purchasing a slide topper for our 2021 Jaco White Hawk 28rl, the slide is 141 inches and is already prepped for a slide topper. Im looking at the solara LCV000177334 topper and want to confirm that that is the correct size for...

I am considering purchasing a 362SA5 for a 5 ft wide trailer door. My concern is knowing that the cable/action is long enough for the door to go all the way down. Should I be measuring something to confirm? Also, it says that it has an 85 pound...