!Liberty Travel Trailer  x   >   !HWT  x   >   !Sprinter  x   >   CE Smith  x   >  

Hi, Long story that I will try to shorten as much as possible. Last year I ordered an axle to upgrade my Harbor Freight trailer Item # 20440I-EZ-60. When I received it there were parts missing which has been taken care of. But due to this issue...

I currently have a single axel travel trailer with an off-road package. The current tire size is LT235/75R15, but I am looking to flip the axel and lower the trailer. What size tire could I use as a replacement non-off-road? | If your springs...

My trailer’s backing plates have carpet on them for the boat to skid on, can this be done on these fenders? | It sure can! The backing plate on the Single Axle Trailer Fender w/ Backing Plate - Steel - 14" to 15" Wheels - Qty 1 # HP36VR you...

I need 2 hubs with all bearings seals and races. My spindle ID is .750 Inside rear of hub 1/.750 Tire size is 4.80 x 8 Trailer is approximately 1200 lbs carry weight What other information do you need? Thanks | The bearings that will match...

This hub fits but is too long. Can’t get the castle nut on. Is there a smaller hub kit? | It sounds like you have an older style trailer axle with the short spindles. You will need a new Spindle # TRU44FR to mount on your axle as the short...

Id like to lower my receiver by 8inch for when I want to use a motorcycle rack. What product can you suggest? Ive seen 2 parts from Curt that look like they might work...replacement shank and multi-ball adjustable ball mount receiver. Am...

Are these brackets, CE26098C-2 correct for the aluminum jeep style fender, HP49VR? If not, which bracket? Also need mounting hardware - do you offer the stainless bolts, nuts and washers? | Yes the brackets part # CE26098G-2 are compatible...

Curious about the mounting hardware on the 60” PVC trailer guides. Does it come with mounting hardware or is that separate and if so what is the additional cost? Thanks | The CE Smith Post-Style Guide-Ons # CE27640 that you referenced does come...

I have a 10 Twin Trawler boat with the two trolling motors recessed in the hull. I saw a picture on their website that shows that the bunk boards are positioned in the middle of the boat which is 5 up from the bottom of the two pontoon shaped...

I have a 2007 EZ Loader Trailer Model EZWV-0-100 700 with a Hub BT150A Oil bath. Looking for a bearing and seal repair kit or also a complete Hub Kit. Hub is a 1-1/16 x 1-1/16 with 5 on 4.5 but perhaps can convert to grease only hub that will...

I have Qty 2 of 2inch x 4inch x 24inch L side bunks that I want to simply replace bc they look old. Can you give me the options for that? Also, why does the bottom have 2 sets of bunks on each side of the boat? My boat is 17.1foot long...

I have a Bolton 18- aluminum boat with an additional 2.5 foot water line platform with 6 inch lip upon which the 90 HP Yamaha motor is mounted. I use an EZ boat trailer with a single axel. No rollers just carpeted bunkers on either side. Will...

I want to use the bunks for my pontoon on my boat lift. Wiil they work? The lift beams are 4inch wide and 6inch deep. | The CE Smith V-Wing Bolster Bracket for Pontoon Boat Trailers # CE26244G you referenced in your question is designed for...

the # TA88545-2 is fit the straight spindle with a diameter of 1? | The Timbren Idler Hub Assembly # TA88545-2 referenced in your question is designed for 2,500 pound axles and it uses the # L44649 inner and outer bearing. This particular bearing...

Could you provide me with the measurements of this product? Specifically the height after the bend. Thanks | The CE Smith Post-Style Guide-Ons for Boat Trailers # CE27636 that you referenced has a height of 75 inches and sticks out up to...

I purchased 40 inch Guide ons for my boat 5 years ago, The metal poles that the PVC pipe mounts on has rusted and needs to be replaced. Do you sell these brackets seperate? | We have replacement parts that should work for you but I wasn't 100%...

I have a 1997 Tigershark Monte Carlo 1000 and I’m curious if this would be a good trailer haul it around with. | The CE Smith Boat Trailer # CE48810 would be perfect to haul your 1997 Tigershark Monte Carlo 1000. The Monte Carlo 1000 is 10'...

This came recommended for my 2019 Apex Nano 187rb but I cannot find info on the page to verify it works with electric trailer brakes? | The CE Smith Trailer Hub Assembly # CE13511 will work with your 2019 Apex Nano but not with electric brakes....

Can I use a 12 inch 5 bolt 4.5 pattern on this axle? Why only 13-15? | The wheel mounting flanges on the hubs that come with the CE Smith Trailer Axle part # CE33201GA-HUB are only compatible with wheels that are between 13 and 15 inch in diameter....

i was looking at the 4ft ce roller bunk rollers if i have an 8ft carpeted bunk do i have to replace with 2 on each side? | Yes, if you have 8 foot long bunks currently then you'd want to install a total of two 4 foot rollers on each bunk like...

I am trying to repair a Venture trailer a customer of mine bought with a 61 Chris Craft Continental loaded on it. The problem is that bow roller is way too wide so it never centers the boat when you load it. He just spent $thousands to have...

What is the thread on this? Looking for a replacement knob for my bike rack and it has 1/2” x13 threads. Or what is your recommendation for a knob for this thread | I reached out to the manufacturer and they said that the # C18090 is a fit for...

Hello. I wanted to change out the axle, bearings, hubs and wheels on my harbor freight trailer. I am building a tear on this frame and wanted to up the weight bearing to 2k. I also wanted better tires to allow for highway speeds. Its there...

Hey etrailer, I have an axle that uses: Bearing Kit, LM67048/25580 Bearings, 10-36 Seal Do you know what size bearing buddy or hub cap I would use? 2.44? Thanks | You are absolutely correct, your hubs will require a grease cap/bearing protector...