Result:

I have a ‘56 airstream. My question is the trailer brake wiring. Do you recommend grounding each magnet wire at the axle area, or running a separate ground wire , along with the blue wire, up to the 7 point connector and tapping into the ground...

I am looking to upgrade the rear lights of my Car Mate 5x8foot utility trailer. I currently have Peterson PM444L lights. I am hoping to use the TLL16RK set however I am not sure if they will fit. The Petersons have the standard 2 inch center...

I have a continuous 10gauge wire between the wheels with electric brakes. I want to tap into that wire and run a single 10 gauge wire to my 7 blade trailer side connector. Ground wires are grounded to frame at the wheels. Question: what’s the...

I have a C.R. 18823 grease seal on my 1956 airstream bubble trailer. It’s 3” OD. Do you have anything comparable? Thanks | Hey Larry, yes we do have a grease seal replacement for what you have with the part # 29031. This has the outer diameter...

HADCO brake drums. I’m converting my ‘56 Bubble airstream to electric brakes. I installed the new backing plates with magnets, shoes etc. Can I use my original brake drums/ hubs, or do I need a special backing plate to bolt on the inside? It...

I’m installing a Curt echo wireless brake controller on my ford ranger. I do not have a 12 vol power wire currently connected to my 7 pain truck re eptacle. The trailer brakes on on a 10 gauge wire T terminating at the trailer 7 point plug. Question:...

Is there anything special about manually adjusting self adjusting trailer brakes? I notice there are 2 little openings in rear of backing plate. One has the wheel. What’s the other opening for? Do I have to move the self adjuster out of the...

I have a 1956 airstream Bubble. It had hydraulic brakes- totallly non functional. Brakes are 12” and 2” wide. My question is can I use my 12” hubs with the new loaded backing plates, or do I need new hubs as well. They are in fine condition. Thanks, Larry...

I bought a curt triflex for my new trailer about 3 months ago. The brake controller worked flawlessly up until about a week ago. One day the controller gave me an ol code. I hooked the trailer up to my buddies truck and no code and the brakes...

Can you put a ball on the rear of a receiver hitch cargo carrier to pull a light trailer? | We do have an easy solution for you to use a cargo carrier and tow at the same time, though you would not be able to put a hitch ball on a cargo carrier...

Will this fit a SAE AP2 01 replacement amber side maker lens for a 2007 Rockwood Freedom 1640 LTD tent trailer? | If your original light is 4" L x 2" W x 1-1/8" D then Optronics light # MC32AB will fit in its place. If you have different dimensions...

HAVE SIGNAL BRAKE FLASHERS BUT NO TAIL LIGHTS HAVE NO POWER AT THE PLUG CANT FIND A BLOWN FUSE HELP | Since you have brake and turn but not taillights, the issue can be a fuse, a relay, bad wiring, or a weak connection. I recommend you first...

Does this with mounting brackets? | Hello Raymond, thanks for reaching out. The mounting brackets are not included with the GE Appliances RV Refrigerator # GE58FR. It requires a GE approved top bracket part BMT-GPV10. This is not something we...

I have a 2007 Ford Ranger sport with the step bumper designed for towing from factory. It has the holes for the breakaway chains for towing and a large lip at the front. The ball is right in the middle in a factory hole. I measured from the...

I have been getting mixed information about using my Ranger as a flat tow vehicle. The owners manual says I can use it as a dinghy. It is a 2WD 5speed. Is this a vehicle I can tow, and what parts do I need to order? It is the sport model....

Which conversion cable do I need for 2007 ford ranger which has the 4 pin connection with the 1 male pin and 3 female pins on the truck see first picture and the trailer has the round with 6 flat and one round male in middle see the picture...

What is meant by stabilizing straps for non-trailer loads? | Non-trailer loads are hitch accessories like bike racks and cargo carriers. Basically anything that is not a trailer that you could put on a hitch. Curt recommends you use a Curt Trailer...

I have a 2007 ford ranger and I am gonna install the Curt 55515 trailer connector does the ecu need to be flashed? | Installing the Curt T-Connector Vehicle Wiring Harness item # C55515 will not require you to flash the ecu on your 2007 Ford...

The camco grill mounting bracket states it allows you to mount your propane grill to your existing RV mounting rail..... Whats an RV mounting rail and where can I purchase such an item? Seems like that item would be under related items | The...

For the hitch Item # C12012 is there drilling required for installing on my 07 ranger? Will this hitch Item # C12012 fit with a full size spare tire? | Drilling is required to install Curt Class II trailer hitch # C12012 on your 2007 Ford Ranger....

I have a 2007 Ford Ranger with a 4 pin for my trailer lights. However, I just got a tear trailer and it comes with a round, 7 pin female end. What part do I need? Thank you | If the trailer you are towing has brakes you will need a brake...

will this part work for my 2007 ford ranger? I want to be able to rent a trailer requiring a 4 way flat end for the trailer side. is there a plug in trailer wiring harness that would not require any splicing? any suggestions, details appreciated. thanks...

Can a 2007 Ford Ranger XLT 4.0 2WD be flat tow ? If so whats needed? | According to the owners manual for your 2007 Ford Ranger XLT 4.0 2 wheel drive you can flat tow your Ranger. If you have a manual transmission you are able to tow an unlimited...

Is this weight distributing for the Ranger? I would prefer a weight distributing hitch the best I can put on. What do you recommend? Also there is a capped plug that seems to be from the factory. Is there something I need to plug into that...