Result:

Articles

Recommended Tire Chains for a 2023 Rivian RS1 275/50 R22

Hello, I’m looking for low profile 16mm or smaller snow chains/cables for my 2023 Rivian RS1 275/50 R22. Would these work? Thanks! | Hey Julie, thanks for the information and the picture! I checked with Rivian and we've only got one set of tire...

Availability of a 2 Trailer Hitch for a 2004 Toyota Matrix to Carry a Bike Rack

hoping this exists. Mostly need for a bike rack, would rather not use a converter. thanks | You are definitely on the right track when it comes to not wanting to use an adapter for your bike rack. The only trailer hitches that are a confirmed...

Bolt Sizes for a 2006 Toyota Matrix Trailer Hitch 24812

Do you know the size of bolts for 06 toyota matrix tow hitch? | All of the hitches available to fit your vehicle are Class I hitches. The most common hitch, 24812, was one which fits with or without the rear fascia. The bolts for that hitch...

Will a 4.80-8 Trailer Tire Fit in Place of a 4.00-8 Tire

I have seed planter with implement tires of 4.00 x 8. Will a 4.80 tire fit? | Yes, a 4.80-8 tire will fit in place of a 4.00-8 tire. That is why a lot of times you will see both sizes in the product's title or description and even on the actual...

2008 Toyota Matrix Trailer Hitch and Bike Rack Recommendation

I was hoping to find a 2inch tow hitch for my 2008 Toyota Matrix base model. My bike rack is 2x 2inch and I was hoping not to use an adapter. All the hitches that I have found thus far have 11/4inch receivers. | Only the larger vehicles like...

Where Do You Measure From On The Trailers Coupler to Install The Pole-Tongue Adapter # EQ95-01-5950?

For the tongue pole adaptor, you mention in the video that it need to be install between 27 to 32 inches from the reveiver in the tongue. Do we mesure from the tip of the receiver or the middle, because if I mesure from the tip of the receiver...

What Size Bolts are Used to Install a Trailer Hitch on a 2010 Toyota Matrix

what is the bolt size , 12mm 1.25,1.50,1.75? thanks | If you look at the instructions for Curt hitch # 12228 which I have linked for you, the bolt size used is M12-1.25 x 30mm. This is a 12mm bolt. This is the size that fits the factory weld...

Recommended Metal Weld on Fender for a 12" Wheel

i need to replace my axle/ spindle. my bearing size is L44649. in and out its is 5x4 1/2 i assume spindle replacement will be p.n tru44fr i need 1. 2 spindles 2. axle tube or what size to get from the metal shopthis is on a jet ski trailer...

Are Load Resistors Needed for LED Backup and Brake/Tail Lights

Im thinking of changing to LED lights. 2010 Toyota Matrix XR . Do you need Load Resistors for backup and brake/tail light LEDs. What would be the cost from you for LEDs. Canadian Vehicle | When changing from incandescent or halogen type bulbs...

Will etrailer Spare Carrier # e98ZR Work with Rivian R1S 20

Does this fit a rivian r1s 20 inch all terrain tire? 275 / 65 / R20 | Hey John, yes the etrailer spare tire mount part # e98ZR that you referenced will work with the wheel and tire Rivian R1S 20 inch all terrain tire that you referenced. |

Troubleshooting Trailer Wiring When Connecting a 4 Flat Vehicle Side to 4 Flat-5 Wire Trailer

I have a 2001 Isuzu Rodeo and was recently trying to connect the connector wires to my trailer. My Rodeo is setup to use a 4 flat female end that runs to 4 wires Ground, Tail, L Turn, R Turn to a converter that connects the 4 wires of the end...

Finding Installer for Curt Hitch on 2009 Kia Rondo

A Curt Trailer Hitch Receiver for a Kia rondo 2009 what car brands aré compatible to install the tráiler Hitch | Hey Adrian, I attached a link to an installer locater that you can use to find someone to install the Curt hitch part # C11031 on...

Would Thule Hullavator Work With Rivian R1S OEM Roof Rack?

Im trying to install the Thule Hullavator on a Rivian R1S. I already have the Rivian Cargo Crossbars so Id prefer to use these if possible. The Hullavator requires the crossbars to overhang and the Rivian Crossbars dont. Is there a way to stackinch...