Replacement Master Cylinder for Aero 6000 Actuator

Question

Question:

I have a Master Tow dolly with the discontinued Aero 6000 hitch. Does #T2480000 directly replace the old hitch? How would I determine where to bolt it to the tongue?

asked by: Richard

0

Expert Reply:

For a replacement master cylinder for your Titan Aero 6000 drum brake actuator you can use Master Cylinder part # T4395100. This comes with everything you will need to complete the install.
(Please note that this item's description says it is for the Aero 7500, but it will also work for your Aero 6000).

If you access the master cylinder from below the coupler it will be pretty obvious how it all installs.

expert reply by: Jameson C

0

Answer 1

For your Titan Aero 6000 the correct replacement master cylinder is the part #T4395100 that you referenced and it comes with the piston inside of it as well.

view full answer...

Answer 2

For a Four Winns Boat Trailer with Titan Aero 6000 Surge Brake Actuator, I recommend replacement using the Titan Zinc-Plated, Leverlock Brake Actuator part #099-175-20 which is ready to go as is and will be a great fit. The reason I recommend…

view full answer...

Answer 3

The Titan Aero 6000 does use a slightly different bolt pattern as the Dexter Coupler part #099-175-20 so while it can work as a replacement you'd have to drill new holes or have the new coupler welded on. The brake line fittings are the same…

view full answer...

Answer 4

It does not come with instructions but it is pretty easy to replace. For your Titan Aero 6000 the correct replacement master cylinder is item #T4395100. This is the replacement master cylinder that works with drum brakes. I was able to find an…

view full answer...

Answer 5

For an Aero 6000 master cylinder kit the part #T4714200042 will work with disc brakes and would be what you would need. This is not a complete kit though and you would need to reuse some components. The drum brake master cylinder wouldn't create…

view full answer...

Answer 6

The Master Cylinder Filler Cap #T4480701 on your Titan Aero 6000 brake actuator does have a small pin hole that works with the diaphragm in the cap to release excess pressure in the reservoir. It may be that either fluid is leaking from this hole in…

view full answer...

Answer 7

Your Titan Aero 6000 will use master cylinder cap #T4480701. There are a few different caps used on various Titan actuators but yours does use this one.

view full answer...

Answer 8

There is a couple of way to determine which wheel bearings and grease seals you will be needed for a trailer axle. First, checking the numbers on the wheel bearings and seal will allow you to select the correct parts for your axle. However, in some…

view full answer...

Answer 9

If you are looking for replacement hubs for your boat trailer, we offer lots of great solutions. The Trailer Idler Hub Assembly #AKIHUB-655-6-EZ-K is a great kit that includes everything you need to replace your 82655 hub. The bearings ( #25580 for…

view full answer...

Answer 10

Pulling the wheels and hubs off of your 5th wheel trailer is the best option when trying to identify what wheel bearings and seals are installed. On the back of the wheel bearings there usually is printed a part number like #L44643. With these…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Replacement Master Cylinder for Aero 6000 Actuator

Product Page this Question was Asked From

Continue Researching