Installation Torque Value for Kodiak Replacement Grease Cap KPCAP
Question:
I noticed the torque for these caps is 20 - 30 lb/ft as indicated on the cap. That seems high. The review video simply says snug. I went with tight enough to keep the o-ring from distorting. Theyre still holding after 1200 miles. Will they continue to stay put?
asked by: Doug L
Expert Reply:
Since the Kodiak grease/oil cap # KPCAP is made of tough UV-resistant polycarbonate you don't need to worry about the torque recommendation on the item. Polycarbonate is a very tough material and you can rest assured that Kodiak would not indicate an inappropriate torque value on their product. Note also that torque is always specified as a range of values, not one specific value.
On initial installation a new part will likely snug up at the lower end of the torque range. If it has been removed several times for maintenance then it may well require the upper-end torque value in order to remain snugly in place. If you have 1200 miles on your caps then I suggest just the routine check before each trip to ensure they are not loosened up. You should not need to cinch them down further if they remain tight. Using the O-rings as a visual guide is helpful but use of a torque wrench will eliminate all doubt.
Product Page this Question was Asked From
Replacement Grease Cap for Kodiak 7,000-lb, 7,200-lb, and 8,000-lb Disc Brake Kits
- Trailer Bearings Races Seals Caps
- Caps
- Oil Cap
- 2.875 Inch I.D.
- Kodiak
more information >
Continue Researching
- Shop: Hydrastar Disc Brake Kit w/ Actuator for Tandem Axle Trailers - 13" Hub/Rotor - 8 on 6-1/2 - 7K
- Shop: Replacement Grease Cap for Kodiak 7,000-lb, 7,200-lb, and 8,000-lb Disc Brake Kits
- Shop: Grease Seals 10-36 (pair)
- Shop: Kodiak Synthetic Bearing Oil for Oil Bath Hubs - 8 oz Bottle
- Shop: Kodiak Hydraulic Brake Line Kit - Tandem Axle - 20'
- Shop: Kodiak Ceramic Brake Pads - Stainless Steel Back - 7,000 lbs to 8,000 lbs
- Q&A: Compatibility Of Kodiak Disc Brake Caliper # KDBC250D With HydraStar Caliper Mounting Bracket
- Q&A: How Much Oil Should be Added to an Oil Lubrication System on Hubs
- Search Results: kodiak disc brakes
- Search Results: kodiak disc brake caliper
- Search Results: oil bath seal
- Shop: Hydrastar Electric-Hydraulic Actuator w/ Line Kit for Disc Brakes - 1,600 psi
- Video: Ultimate Overview of the Grease Seals 10-36 (pair)
- Video: Grease Seals 10-36 (pair) Feature Review
- Q&A: What Type of Oil Should Be Used for Oil Bath Hubs On a Trailer Axle
- Search Results: kodiak disc brake kit 8 rotor hub
- Search Results: khr1389d
- Search Results: oil bath hubs
- Q&A: Does Kodiak XL ProLube Oil Bath Hub Body and Cap # XLPROLUBE1980 Come with Seals
- Q&A: Replacement Hub/Rotor or Lippert 8K Axle with Kodiak 250 Caliper
- Q&A: Recommended Synthetic Bearing Lubricant for Kodiak Oil Bath Hubs
- Article: Most Popular Wheel Bearings
- Q&A: What is the Best Grease for Trailer Bearings
- Shop: Trailer Hitch
- Video: Step-By-Step Installation for the etrailer Hub Bearing Kit - Utility Trailer
- Search Results: trailer brakes
- Video: DeeMaxx Disc Brake Kit Review
- Article: Trailer Wiring Diagrams
- Shop: Trailer Wiring
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
on Trailer Bearings Races Seals Caps
