Troubleshooting Low Voltage Output On Blue Wire From Brake Controller On 2002 Ford F-150
Published 10/09/2014
Products Featured in This Question
Question:
the blue wire voltage low what can be the problem
asked by: Morgan
Expert Reply:
A great way to test the brake controller blue wire output is to use a Circuit Tester, like part # PTW2992. You will want to test the blue wire at the back of the brake controller. If that is low, then there may be an issue with the vehicle wiring. The bulb in the tester will place a load on the wiring, and you can tell if you are getting full voltage by the brightness of the bulb in the tester.
If you find that the bulb is dim with the brake controller set at maximum setting, you will want to check the brake controller ground, power and brake switch wires to make sure they are properly connected.
You can also check the vehicle trailer connector for any signs of corrosion that could be causing the voltage drop. If you find any signs of corrosion, you can clean the connector and then apply some dielectric grease like part # 11755 to the connections. This will help keep dirt and moisture out of the electrical connection and help prevent corrosion in the future.
If everything checks out, you may have a faulty brake controller and will need to replace it.
If you find you need to replace it, I recommend the Tekonsha Prodigy P2, part # 90885. This is a proportional brake controller that will activate the trailer brakes in proportion to your vehicle's braking action. This controller also helps reduce the brake wear on your towing vehicle.
I also recommend the Tekonsha Plug-In Wiring Adapter, part # 3035-P. I have attached a link to an installation video for the P2 brake controller and adapter you can check out.
I have also attached links to some helpful articles for brake controllers you may want to take a look at.
Product Page this Question was Asked From
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Splice-In
- Under-Dash Box
- Under-Dash
- Up to 4 Axles
- LED Display
- Single Trailer Only
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Search Results: 7 way tester
- Search Results: 7 pin connector
- Shop: Dexter Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3.5K
- Q&A: Testing Electric Trailer Brakes Using Direct Battery Power
- Q&A: Testing Electric Brakes on Trailer without Connecting to Tow Vehicle
- Shop: 7-Way Molded Trailer End with 6' Cable - HD Blue Insulated
- Shop: Hopkins 7-Way Molded Trailer Wire Connector - 11' Long
- Shop: etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector
- Shop: Hopkins 7-Way RV Style Connector w/ Molded Cable and LED Test Lights - Trailer End - 6' Long
- Shop: 7-Way Molded Trailer Wire Connector, 6' Long
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 12" - Left/Right Hand - 5.2K to 7K
- Article: Testing Brake Controls
- Search Results: dexter 4440558
- Q&A: Troubleshooting Voltage Output from Electric Brake Controller on 2017 Chevrolet Silverado 2500 HD
- Q&A: Tips to Improve Voltage Drop from Trailer Connector to Back to the Rear Light Assemblies
- Q&A: Picking Out Brake Assemblies for Camper Trailer
- Q&A: Where is Fuse for Trailer Brake Controller on 2016 Ford F-150
- Shop: Brake Controller
- Q&A: Solution for Powering Brake Controller Install of 2019 Ford F150 with Factory Tow Package
- Search Results: splice
- Search Results: electrical tape
- Search Results: silicon
- Video: Liquid Electrical Tape Spec Review
- Video: The Low-Down on the Deka Self-Fusing Auto Tape