Weight Distribution Hitch for 2026 Ford F-350 Tremor Towing a 2026 Salen Hemisphere 308RL
Updated 11/18/2026 | Published 11/17/2026 >
Question:
My 2026 ford f-350 tremor is factory taller. will i need a different shank for the 16k bandw continuum weight distribution hitch to pull my 2026 salem hemisphere 308rl?
asked by: Jamey
Expert Reply:
Hey Jamey!
Congrats on your new setup!
I did some research into this for you and I don't think you'll need a different shank. The factory height of the 2026 Ford F-350 Tremor isn't listed, but I'm finding online from some forums (which aren't confirmed information, but helpful in this case) that the top of the receiver sits about 24" from the ground. You'll want to measure your truck to confirm this measurement when you get a chance.
I ran into the same situation for the 2026 Salem Hemisphere 308RL, where there is no confirmed height. With that, I found that some older models of the Hemisphere sat around 20"-22-1/2" from the ground.
With that, the B&W Continuum Weight Distribution System # BW28FR that you were looking at will almost definitely be a really good system for you. It includes 2-1/2" shank for you to match up with your factory receiver, and the head is adjustable in 1-3/4" increments for up to 3-1/2" of drop or 9-3/8" of rise.
Just to break that down a little more, if your truck's hitch sits at 24" from the ground, the coupler can sit anywhere between 18-1/2"-35-3/8" off of the ground, because you'll want the trailer to be within 2" of level, though exact is always better.
What trips do you have planned for the Hemisphere? Is this gonna be a full-time rig or do you just plan to take it out on weekends and vacation trips?

Terry
11/18/2026
24K miles on this hitch with my 2026 F250 and Brinkley Z Air 285. Alabama to Alaska and back, still love it.
Product Page this Question was Asked From
B&W Continuum Weight Distribution System w/ Sway Control for 2.5" Hitch - 16K GTW, 1.6K TW
- Weight Distribution Hitch
- WD With Sway Control
- Hydraulic System
- Fits 5 Inch Frame
- Fits 6 Inch Frame
- Includes Shank
- 2-5/16 Inch Ball
- Fits 2-1/2 Inch Hitch
- Allows Backing Up
- 1000 lbs
- 1100 lbs
- 1200 lbs
- 1300 lbs
- 1400 lbs
- 1500 lbs
- 700 lbs
- 800 lbs
- 900 lbs
- B and W
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: Will the 2-1/2" B&W Continuum Weight Distribution System Provide Tailgate Clearance?
- Q&A: Will Standard B&W Continuum Shank Allow Tailgate To Open On 2026 Ford F-250 King Ranch
- Q&A: Will B&W Continuum Work With 2024 Ram 2500 Towing Alliance Delta 292RL
- Q&A: Recommended Weight Distribution For 35' Travel Trailer with 1,050LBS Tongue Weight to Prevent Sway
- Q&A: Can B&W Continuum Head With 2-1/2" Shank Replace Head With 2" Shank
- Q&A: Does the B&W Continuum Really Need the Grease Checked Every 250-500 Miles?
- Article: 5 Things to Know About Weight Distribution Hitches
- Q&A: Weight Distribution System For Towing A Grand Design Imagine XLS23LDE With A Ford F-250
- Article: 2 Steps for Finding the Right Weight Distribution Hitch Size
- Article: Top Weight Distribution Hitches for a Buttery Smooth Ride
- Article: Which Sway Control Hitch is Right For Your Trailer?
- Article: How to Measure for Trailer Hitch Drop
- Article: Hitch Adapters and Extenders
- Article: How to Winterize & De-Winterize Your RV (Simple Guide)


Jamey
11/17/2026
I will have to get some measurements this evening after work. I’m sure that I will have more questions in a few days after I get measurements. I pull the camper several times throughout the summer with my longest trip being 375 miles one way. Thank you.