Parts Needed to Add a Battery to a Enclosed Trailer
Updated 11/16/2026 | Published 11/14/2026 >
Products Featured in This Question
Question:
Hello, I have a Sawyer enclosed trailer that uses the Brightway trailer breakaway kit 5Ah, factory installed. Sawyer wired the three exterior white lights and one interior ceiling LED strip to the battery in this breakaway kit. The lighting hardly lasts, if it comes on at all there's a chance the interior strip is no good, and the Brightway cover panel perpetually shows charging seemingly regardless of how much drive time vs. use time anything has had. Bottom line: I have little confidence in the breakaway and also want better lighting function. I am wondering if you can recommend for me some parts that would enable putting an RV or marine battery in the trailer, charging it from the truck, and then using it to power the lights, likely an electric jack, and the breakaway. I realize that depending on usage, I might need to charge the battery from shore power given its size relative to trailer cable power. Thank you!
asked by: Fred G
Expert Reply:
Thanks for all the information Fred. To add a battery to your Sawyer enclosed trailer you will need the following parts:
etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box item # e99011
Go Power AGM RV Battery item # 34276285
Attwood PowerGuard Pro Battery Box for 24/27/31 Batteries item # AT69RR
10 Gauge Wire item # 10-1-1
Our etrailer junction box item # e99011 will add a 7-Way connector to your trailer along with a convenient storage box that will consolidate your trailer's wiring. You'll then run 10 Gauge Wire item # 10-1-1 from the black colored terminal to the positive post on the AGM RV Battery item # 34276285. You can then connect the positive wire of your Bright Way charger/breakaway system to the positive terminal of the item # 34276285 battery or directly to the 12V auxiliary feed from the trailer's 7-way junction box item # e99011. This will power your breakaway battery and you can also tie in your trailer's light circuits as well. Your truck's 7-way will keep the battery topped off while you're driving.
To add a shore power connection, you'll need the 30 amp Safe View Smart Power Inlet item # HU87VR and the WFCO RV Power Center item # WF28FR. Since you don't have a large power demand a small charger like the NOCO item # 329-GENIUS5 could plug into a power inlet like the NOCO item # 329-GCP2 and you could then just run a normal extension cord over to your shore power.
What do you typically haul or use your Sawyer trailer for? Feel free to answer this and throw in any other questions you have, where it says Add Comment.
Product Page this Question was Asked From
etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector
- Trailer Wiring
- Trailer Connectors
- Trailer End Connector
- 7 Blade
- Plug and Lead
- etrailer
more information >
Continue Researching
- Article: Trailer Wiring Diagrams
- Q&A: How to Replace a Lance 6-Pin Plug w/ a Standard 7-Way Connector
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Trailer Lighting Requirements
- Q&A: Instructions to Wire a Trailer for Electric Brakes
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Article: Breakaway Kit Installation for Single and Dual Brake Axle Trailers
- Q&A: What Gauge Wire Should be Used to Wire Trailer Brakes
- Q&A: How to Replace a Lance 6-Pin Plug w/a Standard 7-Way Connector
- Q&A: Comparing the eTrailer and Dexter Electric Trailer Brake Kits
- Q&A: Recommended Junction Box and 7-Way Connector to your Replace a Lance 6-Pin and How to Wire It
- Q&A: Does Dexter 12V KTI Hydraulic Pump Come With Oil



