Replacing Bulb on Peterson Square Trailer Tail Light # 432400
Updated 07/31/2014 | Published 07/30/2014 >
Question:
How do you remove and replace the trailer lights
asked by: Don
Expert Reply:
To change the bulbs in Peterson trailer tail light # 432400 you will first remove the main lens which is held on by 4 screws.
The main bulb can be removed by pushing down and rotating the bulb counterclockwise. There is a diagram on the inside of the case that explains this and it says turn it 30 degrees then pull up. I had to turn it several more times when I played with the light so it probably varies slightly.
To install a new 1157 bulb # 30-90-157 you will line up the lower nub on the light base with the upper slot and push the bulb in. It will snap into place. This is also shown on the inside of the light in a little diagram.
The other bulb just pulls right out.
Product Page this Question was Asked From
Peterson Combination Trailer Tail Light - 7 Function - Incandescent - Square - Driver Side
- Trailer Lights
- Tail Lights
- Brake/Tail/Turn
- License Plate
- Marker
- Square
- Surface Mount
- Non-Submersible Lights
- Incandescent Light
- 4-3/4L x 4-1/2W Inch
- Red
- Peterson
more information >
Continue Researching
- Search Results: trailer lights
- Shop: Optronics Fleet LED Trailer Tail Lights w/ Grommets - Stop,Turn,Tail - Submersible - Oval - Qty 2
- Video: Detailed Breakdown of the Replacement Spindle Washer
- Video: Remove and Reinstall a Trailer Hub Review
- Search Results: 10 60 seal
- Search Results: hub
- Search Results: grease seals ~ double lip trailer bearings races seals caps
- Q&A: Recommended Pregreased Idler Hub w/a 5 on 4-1/2 for a L44649 Straight Spindle
- Shop: Vehicle Tow Bar Wiring
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Shop: Optronics LED Trailer Tail Light - Stop, Turn, Tail - Submersible - 10 Diode - Oval - Red Lens
- Shop: LED Trailer Light w/ Grommet - Brake, Turn, Tail - Oval - Red
- Shop: Base Plate for Tow Bar
- Shop: Lippert Grease Seals - Double Lip - ID 1.5" / OD 1.987" for 2K to 2.5K Axles
- Video: An In-Depth Look at the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit
- Search Results: ez lube grease cap
- Search Results: lug
- Q&A: How to Identify Correct Replacement Grease Seals and How to Install Them
- Q&A: Replacement Hub for 1991 Bass Tracker Boat Trailer
- Q&A: Replacement Trailer Idler Hubs For a 2007 Tracker TrailStar Boat Trailer
- Q&A: Difference Between Grease Seal 10-9 and 10-60
- Q&A: Method for removing and Installing Tang-Style Spindles Washers
- Q&A: Where to Measure on Trailer Spindles to Determine Replacement Hubs
- Search Results: blue ox tow bar
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Video: Let’s Check Out the CE Smith Deep V Keel Roller Assembly for Boat Trailers
- Shop: Trailer Hub Assembly - 2,200-lb E-Z Lube Axle - 5 on 4-1/2 - 13" - 15" Wheels - Galvanized
- Shop: Roadmaster Bulb and Socket Tail Light Wiring Kit w/ 7-Way to 6-Way Adapter Cord - Red LEDs
- Shop: Blue Ox Base Plate Kit - Removable Arms
- Shop: Trailer Wiring

