How Does X LED Truck and Trailer Tail Light part # BUL602CRB Get Wired Up
Updated 10/05/2026 | Published 09/29/2026 >
Question:
Purchased these X LED Truck and Trailer Tail Light w/ Reverse Function - Submersible - Oval - Red and White - Tail Lights in May. Finally getting around to installing them, but having an issue. Wired one w/ 3 wires but no reverse lights. Wired the second light and reverse light remains ON, ALL the time. What is the correct method or wiring when reverse lights are desired??? BUL602CRB
asked by: Patrick P
Expert Reply:
Hey Patrick, when wiring in the X LED Truck and Trailer Tail Light part # BUL602CRB the white wire is the ground, black is the taillight function, and then red is for the reverse light and it is what activates the white LEDs. I am sure it's just the case that you have the wiring mixed up so that would be what I would check and fix as needed.
Product Page this Question was Asked From
X LED Truck and Trailer Tail Light w/ Reverse Function - Submersible - Oval - Red and White
- Trailer Lights
- Tail Lights
- Backup
- Oval
- Recessed Mount
- Submersible Lights
- LED Light
- 6-1/2L x 2-3/8W Inch
- Red
- White
- Optronics
more information >
Continue Researching
- Search Results: oval trailer light
- Search Results: round grommet
- Shop: Rubber Grommet for Custer 2" Round Side Marker and Clearance Lights
- Shop: Optronics LED Trailer Utility Light - Submersible - 3 Diodes - Round - Clear Lens
- Video: Review of TecNiq Trailer Lights - Tail Lights - TN97AR
- Shop: Optronics Fleet LED Trailer Tail Lights w/ Grommets - Stop,Turn,Tail - Submersible - Oval - Qty 2
- Shop: TecNiq Stop Tail Turn Reverse Light - 6" - Oval - Amp Plug - Grommet Mount
- Shop: Fusion LED Trailer Tail Light - Stop, Tail, Turn, Backup - Submersible - Oval - Clear Lens
- Shop: TecNiq LED Trailer Tail Light - Stop, Tail, Turn, Backup - Submersible - Oval - Red/Clear Lens
- Shop: Fusion LED Trailer Tail Light - Stop, Tail, Turn, Backup - Submersible - Oval - Red/Clear Lens
- Search Results: trailer lights
- Shop: Trailer Hitch
- Search Results: timbren vehicle suspension
- Shop: Trailer Wiring
- Q&A: Replacement Stop/Turn/Taillight With Back Up Lamp for Eagle Boat Trailer
- Q&A: Installation of Breakaway Kit Switch for Electric Trailer Brakes on Gooseneck Trailer
- Q&A: How To Wire Light Bar On Trailer With Switch In Vehicle
- Q&A: Will Aluminum Transition Plate Bend On Enclosed Trailer When Loading Heavy Zero Turn Mower?
- Q&A: Replacing TDE 70LP On Swing Away Tongue
- Q&A: Titan BrakeRite Disc Brake Actuator Will Not Build Up Pressure After Sitting For Several Years
- Q&A: What Light Will Replace My Light with DOT 16P2ST2 T35 16 Stamped on it for My Truck?
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Trailer Lighting Requirements
- Article: Trailer Wiring Diagrams
- Article: 5 Things to Know About Weight Distribution Hitches
- Article: How to Install E-Track in 3 Easy Steps
- Article: Stability Control for Heavy Duty Vehicles


Jack
10/2/2026
3 days after I got my truck, so.eone hit my back bumper hard enough to dent it. I installed a pair of these lights in the bumper. I ran wires down from each taillight to my new bumper light. Black is not ground like you may think. I ran the black to my brake/turn light and red to my backup.