Upgrading Older Weldex Rear Camera System In 2006 Holiday Rambler Class A RV
Updated 09/24/2026 | Published 09/22/2026 >
Question:
I have a 2006 Holiday Rambler class A with a weldex rear camera system, monitor model WDRV-3467M. I am having trouble withe the camera or monitor not sure witch. Is there a plug and play system for this setup?
asked by: John
Expert Reply:
Hey there John.
Thanks for the pictures! You have the older Weldex WDRV-3467M 7" monitor.
You have two good options here. The easiest is to stay with Weldex. Their newer WDRV-7063M-UPGD monitor kit is designed to replace your older monitor and reuse the existing Weldex wiring. If the rear camera is the problem, the WDRV-7063C is also made to work with the existing 6-pin cable. We do not carry those Weldex replacement parts, though, so you'd need to source them elsewhere unfortunately.
The other option would be to replace the entire system with a newer setup that we carry. Something like the Rear View Safety # RVS-7707721 would work well, but it is not a direct retrofit for the old Weldex monitor. You would remove the old monitor and mount the new display on the dash, so some modification or cleanup of the old monitor area may be needed. It would also require running the new camera wiring or adapting the existing wiring.
Does your monitor still power on and just show no picture, or does it not power on at all?
Maybe we can try to troubleshoot it so you don't have to replace everything. A lot of times there is just a ground or power issue in the wiring.
Product Page this Question was Asked From
Rear View Safety Backup Camera System with Flush Mount Camera
- RV Camera System
- Backup Camera
- Mirrored Image
- Night Vision
- Hardwired
- Wide View
- Dashboard Pedestal Mount
- Rear
- 7 Inch Display
- 1 Camera
- Rear View Safety
more information >
Continue Researching
- Search Results: tow bar
- Search Results: slide motor
- Search Results: roadmaster tow bar
- Search Results: 154
- Search Results: brake light switch
- Search Results: roadmaster 521453~5
- Search Results: dometic 320 parts
- Shop: Air Lift LoadLifter 5000 Air Helper Springs - Rear Axle
- Shop: 12 Volt Outlet Kit, 20 amps
- Shop: Roadmaster Falcon 2 Tow Bar - RV Mount - 2" Hitch - 6,000 lbs
- Shop: Pacbrake Alpha XD Air Bag Suspension Kit - Rear Axle - 7,500 lbs
- Shop: RV Designer Motorhome Entrance Door Lock w/ Deadbolt - Black
- Shop: Roadmaster Stop Light Switch Kit
- Shop: Roadmaster Universal Stop Light Switch Kit
- Video: DIY Install: etrailer XHD Non-Binding Tow Bar on your 2020 Ford Expedition
- Video: Review of SuperSprings Intl Vehicle Suspension - Towing/Load Leveling - SS69PV
- Video: An In-Depth Look at the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit
- Shop: Base Plate for Tow Bar
- Q&A: Upgrading Older Weldex Rear Camera System In 2006 Holiday Rambler Class A RV
- Video: An In-Depth Look at the Roadmaster Battery Charge Line Kit for Towed Vehicles
- Shop: Vehicle Tow Bar Wiring
- Video: Comparing Portable Flat Tow Braking Systems - Curt RVi and Blue Ox Patriot
- Shop: Vehicle Tow Bar Brake System
- Shop: Trailer Hitch
- Video: Breaking Down the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit
- Video: Review of Roadmaster Tow Bar - Hitch Mount Style - RM27NQ
- Shop: Trailer Wiring
- Shop: Suspension Enhancement
- Shop: Brake Controller
- Q&A: Is There a Support Brace Designed for the Replacement Crank Extension for Lippert Spare Tire Winch?





John
9/23/2026
Lately when I start the motorhome the monitor comes upas normal then after a while the screen will go white. I turn off and back on to the power to the monitor with no change. When I turn off the motorhome and restart it the monitor comes back as normal. The cycle continues.