Looking For 7' Long Brake Line To Go With Dexter K71-773-01 Calipers

Question

Question:

I just ordered a Dexter brake caliperdrivers side and I also need a 7’ brake line as well but I could not find what would work. Any help would be appreciated. Thanks.

asked by: Paul Z

0

Expert Reply:

Hey Paul, thanks for reaching out. We do have brake lines that go with the Dexter # K71-773-01, and we do have a flexible line that is exactly 7' long. Here is what I recommend:

- Kodiak Hydraulic Brake Hose - 3/16" Male Fittings w/ Stainless Flares - 1/8" ID - 7' # bh-3mfs-7

What kind of trailer is this for?

expert reply by: Jesse M

0

Kodiak Hydraulic Brake Hose - 3/16" Male Fittings w/ Stainless Flares - 1/8" ID - 1'
(click to enlarge)

Dwight V.

8/15/2026

The brake line I ordered it my Dexter axle exact. It worked great.

Thomas B.

8/16/2026

@DwightV I had same experience. Its installed works great

Answer 1

We have just what you need based on the dimensions you listed. The correct grease seal you need is the part #168255TB which has outer diameter of 2.561 and an inner diameter of 1.687 inch.

view full answer...

Answer 2

The Titan Replacement Reverse Lockout Solenoid you mentioned is extremely easy to wire. The solenoid has two wires exiting it. One wire grounds to the trailer tongue, the other would connect to the reverse light circuit on the tow vehicle. Once…

view full answer...

Answer 3

The DB-42 is an older style of UFP 3,500 lb axle disc brake components. The Kodiak kits like the part #K2HR35D will fit in replacement of that and would be an upgrade so this would be a great solution. It comes with everything you'd need to…

view full answer...

Answer 4

Hey Jeff, we can definitely help but the pins that go into the breakaway switch are not all universal and unless you know what brand it is the best solution is to just replace the entire switch like with the part #420000 as this approach is universal…

view full answer...

Answer 5

Hi Dan; those couplers are no longer around so we do not have a direct replacement. What you can do is pick up a piece of stock steel to extend the tongue and add a Fulton Fold-Away Coupler Hinge. Then you can add an actuator like the #DM72VR or…

view full answer...

Answer 6

Hey David! For a disc brake conversion I recommend the DeeMaxx Disc Brake Kit #DE42FR. These are designed to fit a 5 on 4-1/2 bolt pattern and are rated for 3,500 lb axles. Make sure this matches your axle capacity. They are also compatible with your…

view full answer...

Answer 7

I did some research on your 2006 Marine Master Tandem Axle Trailer and found some of the UFP part lists. Dexter owns that company as well as the Kodiak line, so the parts are extremely similar with different part numbers that should work very well as…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 11

Hey George! I do have brakes made specifically for your Demco KK260 Kar Kaddy! Demco Hydraulic Drum Brake - Single Servo - Galvanized - 10" - LH - Self-Adjusting - 3,500 lbs #DMSB24429M and Demco Hydraulic Drum Brake - Single Servo - Galvanized…

view full answer...

Looking For 7' Long Brake Line To Go With Dexter K71-773-01 Calipers

Product Page this Question was Asked From

Continue Researching