What Portion of the Wiring for the Yakima Rack and Roll Trailer is the Part # Y8880203

Question

Question:

Is this wiring harness Y8880203 the entire wiring system for the Yakima trailer from the tongue to the tail lights?

asked by: Jim

1

Helpful Expert Reply:

The Replacement Tongue Wiring Harness # Y8880203 is just the section of the wiring that runs down the main channel of the frame. There are also other harnesses that my contact said you would need to contact them directly to get.

expert reply by: Jameson C

1

Answer 1

The Thinline LED Light #MCL65CRB will allow you to replace the Incandescent Light #M154C which comes with the License Plate Kit #8880166 for the Yakima Rack and Roll trailer. The light housing is sealed to keep water out so it must be replaced as a…

view full answer...

Answer 2

Yes, replacement wiring harness #Y8880203 is the main, long wiring harness for Yakima Rack and Roll trailers. The shorter harness, which is used if adding the tongue extension, is #8880161. And the rear lighting harness, should you need it, is…

view full answer...

Answer 3

Part #Y8880203 and #8880161 would be the wiring for the tongue while part #8880162 would be needed for the rear lights. The balance of the wiring is run inside the framework of the Rack and Roll trailer. Since you said you are replacing all of the…

view full answer...

Answer 4

You are correct, the Replacement Tail Block Locking Assembly #8880334 is only for the 2015 and up model year Rack and Roll trailers. According to Yakima, the reason is the thickness and length of the shaft was increased, so it's a different size.…

view full answer...

Answer 5

The Replacement Tongue Wiring Harness #Y8880203 is just the section of the wiring that runs down the main channel of the frame. If you had the tongue extension as well you'd want the part #8880161 as well. The rear harness is the part #8880162.

view full answer...

Answer 6

I have attached below a list of the replacement parts we offer for the Yakima Rack and Roll Trailer part #Y08106 which relate to the lights and wiring. If you don't see something you need just let me know what that is. Replacement Side Marker…

view full answer...

Answer 7

You'll need to remove the ring terminal screws that hold the white wires of the #8880162 to the trailer but then the other connections simply plug into the female matching end on the trailer since it uses bullet connectors.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

What Portion of the Wiring for the Yakima Rack and Roll Trailer is the Part # Y8880203

Product Page this Question was Asked From

Continue Researching