Resetting a Titan Surge Brake Actuator # T4747200

Question

Question:

If the breakaway lever failsafe is tripped accidentally how would it be reset?

asked by: Jason

0

Expert Reply:

To release the breakaway lever of the Titan Zinc-Plated Brake Actuator # T4747200 you will need to use a screw driver to push the clip on the lever back towards the rear of the trailer while pushing the lever back to its original position.

expert reply by: Jameson C

0

Answer 1

That’s a great question, Jorge - this one can definitely be a little tricky the first time you run into it. On the Dexter/Titan Model 6 actuator like yours, resetting the breakaway lever isn't to difficult. To reset it, you’ll first want to…

view full answer...

Answer 2

The cap and roller are held onto the shaft by a pal nut. The best way to remove the pal nut is to grab it with a pair of pliers and rock it back and forth until the pal nut deforms enough to pull off the end of the shaft. A pal nut is a one-time use…

view full answer...

Answer 3

Hey Dave, To retract the breakaway cable, slide the coupler fully forward and push up on the pushrod release bracket located on the underside and behind the hitch ball socket to allow the bead to retract into the actuator. This will release the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Resetting a Titan Surge Brake Actuator # T4747200

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching