Tallboy Bottle Jack With Big Foot Plate For Jacking Up Utility Trailer 5,000lbs

Question

Question:

Would this work for changing a flat on my small utility trailer? total weight is close to 5k I think when loaded. thanks

asked by: Carol

0

Expert Reply:

Absolutely, Carol. The 2-ton Tallboy # PM44FR is great for utility trailers, small campers, and light cargo haulers. It’ll easily lift one corner of a 4,000-5,000-lb trailer, and the U-shaped saddle cups the axle nicely, so it doesn’t slip. Just make sure the jack’s 7-15/16 inch starting height fits under your axle - if your trailer sits low, drive the good tire up on a short board first to gain a couple inches of clearance.

Do you usually tow that trailer with an SUV or pickup?

expert reply by: Andrew N

0

Carol

11/3/2025

We usually pull it with our F-150, mostly landscaping stuff, mower, mulch, all that. I’ve had two flats this year, so I’m ready to make things easier next time.

Andrew N.

11/3/2025

@Carol Sounds like a plan, Carol - those landscaping or agriculture jobs can be hard on tires! The Tallboy will make your life a lot easier when you’re on uneven ground or gravel.

Answer 1

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 2

Hey Don! Yes, the base can be removed from the Power Mountain Tallboy Off-Road Bottle Jack #PM34FR. All you need to do is remove the bolts that attach it to the base and you can remove it and store the jack. What kind of setup do you have?

view full answer...

Answer 3

Good morning Bobbie! Sorry for the troubles you were having; I've been there before and know exactly how you feel. I have a great option for you, but the jack you were looking at - Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 4

Hello Gary, thanks for reaching out. The Power Mountain Tallboy Off-Road Bottle Jack #PM34FR has a lift (throw) range from 8.5 inches to 37.75 inches. So whatever you’re planning to lift with it, you’ve got plenty of headroom and reach based on that…

view full answer...

Answer 5

Bryce, the Power Mountain Tallboy #PM44FR is strong enough to lift your 4Runner, but it does need room to fit underneath. With a minimum height just under 8", it works great for tire changes or light trail repairs - as long as your frame or axle…

view full answer...

Answer 6

Hey Todd! At the lowest setting, the saddle of the Power Mountain Tallboy Off-Road Bottle Jack #PM34FR sits at 14" and the top of the saddle arms are at 15-3/8". I took a photo of it out in our warehouse, and while I wasn't able to get…

view full answer...

Answer 7

Hi Joe; the Power Mountain Tallboy Off-Road Bottle Jack #PM34FR starts off at 8.5" tall with a lift up to 14.25" without adding any extensions as seen in the attached photo. The shortest extension is 5" so it would extend up to…

view full answer...

Answer 8

Hey Lynn, are you asking about the dimensions of the base of the Power Mountain Tallboy Off-Road Bottle Jack #PM34FR? If so, the base is 8 by 7 inch and this has a 12,000 lb lifting capacity so it would lift a 12k fifth wheel by the frame as well.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Tallboy Bottle Jack With Big Foot Plate For Jacking Up Utility Trailer 5,000lbs

Product Page this Question was Asked From

Continue Researching