Is there Pre-Cut Holes for Water Supply and Shower Head on the Specialty Recreation RV Shower?

Question

Question:

Will I have to self-drill the holes for the water supply for the shower head?

asked by: John L

0

Expert Reply:

Hello John,

Great question!

The Specialty Recreation RV Shower and Tub Surround - 32" W x 23-3/4" D x 66" T - White # SR75RR does not have any pre-cut holes, so you will need to cut them yourself for the water supply and shower head.

What kind of camper are you putting this in?

expert reply by: Kate F

0

Shower Walls with No Pre-Cut Holes
(click to enlarge)

Kate F.

12/1/2025

Hey John, how did cutting the holes for the water supply and shower head go with your shower surround? Your update could make it easier for the next person working on a similar camper setup.

Answer 1

Hi Bob; the walls referenced in the instructions are the literal walls, different from a surround/panels like #SR75RR which would be installed after you get the Specialty Recreation RV Shower Pan #SR23RR in place. Regardless, you need to use ABS…

view full answer...

Answer 2

A door for the Specialty Recreation RV Shower and Tub Surround #SR75RR is not something that we carry. We actually don't have any shower doors at this time. You would have to find one that will fit from an online retailer that carries doors or…

view full answer...

Answer 3

Hey Heather, while I am not sure which specific Specialty Recreation RV Shower Pan you are referring to I can tell you that they can be used with other brand surrounds as they are designed to be as universal as possible. Which pan and surround were…

view full answer...

Answer 4

Yes, it will John. So long as your shower pan matches the dimension of the Specialty Recreation RV Shower and Tub Surround - 36" W x 23-3/4" D x 66" T - White item #SR85RR it will work. What kind of trailer or motorhome do you have?

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Is there Pre-Cut Holes for Water Supply and Shower Head on the Specialty Recreation RV Shower?

Featured Help Information

Miscellaneous Media

Continue Researching