What is Length of Replacement Support Arm for Thule Omnistor 5200 Motorized Awning

Question

Question:

What’s the length of the support arms?

asked by: Jared B

0

Expert Reply:

Hey Jared, the length of the Replacement Support Arm for Thule Omnistor 5200 Motorized Awning # LC62TF that you referenced is 1.9 meters.

expert reply by: Jameson C

0

Jared L.

10/14/2025

Is that extended or collapsed?

Jameson C.

10/14/2025

@JaredL That would be extended.

Answer 1

We do have the Replacement Support Arm #LC62TF which is the Lippert part number 656608.

view full answer...

Answer 2

Hey John, thanks for reaching out! I unfortunately don't have the length of the Replacement Support Arm for Thule Omnistor 5200 Motorized Awning #LC62TF, but what I can say is this is designed to fit the Thule Omnistor 5200 Motorized Awning so if…

view full answer...

Answer 3

Hello Ryan. It may be possible to replace the arm assembly for your awning, but there is no way to look up your camper to know what brand and model of awning it is equipped with. The arm assemblies are brand specific so please confirm for me what…

view full answer...

Answer 4

Hello Bruce, thanks for reaching out. The Dometic Penguin II High Capacity RV Air Conditioner #DMC29ZR does not include a heat strip and there is not a separate heat strip that can be added. We do offer this same AC unit with a heat pump, and that…

view full answer...

Answer 5

Hi Christopher, The Replacement Support Arm for Thule Omnistor 5200 Motorized Awning #LC62TF should come with two arms and not just one, it will include everything you see in the picture attached below. This comes with two wall brackets to lock the…

view full answer...

Answer 6

Hello Phil, thanks for getting in touch. The MaxxFan Deluxe #MA00-07500K is a great choice for a vent fan and it can be used to replace your current vents. This vent can only be operated with the manual controls on the vent itself, or with the…

view full answer...

Answer 7

If you have already added the fuse and the trailer charge circuit is not activated in the 2019 Ford F-350 Super Duty with factory integrated brake controller, then you want to make sure the trailer is connected and you press the brake according to a…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

What is Length of Replacement Support Arm for Thule Omnistor 5200 Motorized Awning

Product Page this Question was Asked From

Continue Researching