What do you Torque the 1/2" Hardware to When Installing the TowSmart Trailer Hitch Receiver?

Question

Question:

Do the bolts for the hitch get torqued to a certain spec

asked by: Joe S

0

Expert Reply:

Hello Joe,

According to the instructions for the TowSmart Trailer Hitch Receiver - Custom Fit - Class III - 2" # TS36VR you will need to torque the 1/2" hardware to 110 ft-lbs.

What do you plan on using the hitch for?

expert reply by: Kate F

0

Torque Specs in Instructions
(click to enlarge)

Joe S.

8/27/2025

I’m planning on using the hitch for pulling a small horse trailer

Kate F.

8/27/2025

@JoeS I'm jealous Joe! But first I need to get a horse to need a trailer. I showed western as a kid and would love to have some horses of my own some day. Enjoy your horses =)

Answer 1

The Redarc Encapsulated Power Diode #RED34FR is only needed on vehicles with certain advanced safety systems like the Adaptive Cruise Control, Assisted Emergency Braking and Autonomous Emergency Braking. If your 2016 Toyota Highlander has these…

view full answer...

Answer 2

Hey, William! No cause for concern! The 4th wire on the Redarc harness part #RED93RR is for the California Vehicle Code 26458. This compliance means that when you press the manual override on the brake controller (to apply trailer brakes without…

view full answer...

Answer 3

No, you do not Jeff. The Redarc Tow-Pro Trail Brake Controller w/ Custom Harness item #RED74UR is a plug and play setup for your 2022 Toyota 4Runner. It already has the necessary wiring and diodes so the item #RED34FR diode is not needed. What kind…

view full answer...

Answer 4

Hey Rob, thanks for reaching out! The unibody definitely can be a problem, especially when the owner's manual discourages it. I get the concept behind the Anderson WD hitch, but frankly I'm a little skeptical of it myself, so I have some…

view full answer...

Answer 5

We currently do not have any installation videos for the Redarc Encapsulated Power Diode #RED34FR being used to install the Redarc Tow-Pro Liberty Brake Controller #RED24FR with the Harness #RED69FR and Panel #RED48FR for any vehicles or your 2021…

view full answer...

Answer 6

The Redarc Encapsulated Power Diode #RED34FR shouldn't be needed for installing the Redarc Tow-Pro Liberty #RED24FR and Pigtail #RED69FR on your 2020 Subaru Forester. The answer page you're referring to didn't have us telling someone to…

view full answer...

Answer 7

Hi Pete; the #RED44FR installation video doesn't actually show the typical connection to the brake light trigger using the red wire since they ran extra wire and routed it to the back. You can follow the video or you can identify the cold side of…

view full answer...

Answer 8

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 9

Hey Danial, thanks for the follow up question! Your 2024 Toyota Highlander will just need the 7-Way Kit #ETBC7 along with the Curt Echo In-Line #C79DR. With this setup you won't be splicing into the stop light switch on your Highlander so even if…

view full answer...

Answer 10

Hello Dan, We can most definitely get you set up to use your Redarc Tow-Pro Liberty brake controller in your 2022 Toyota Highlander. Since you were looking at the #ETBC7, I’m assuming your Highlander does not have the factory tow package. To equip…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

What do you Torque the 1/2" Hardware to When Installing the TowSmart Trailer Hitch Receiver?

Product Page this Question was Asked From

Continue Researching