Will the Replacement Anti-Rattle Hitch Pin Work w/ a Toyota 2" Receiver?

Question

Question:

How long is the threaded hitch pin?? I have a 2024 Tacoma and need at least a 4"pin length.....

asked by: Tony

0

Expert Reply:

Hey Tony. The Replacement Anti-Rattle Hitch Pin for Curt Bike Racks item # C82NR is only 3.8” long so it's not going to work with that wider 2" receiver Toyota has decided to go to.

If you're needing a new locking anti-rattle, threaded hitch pin for your Swagman E-Spec Bike Rack item # S94FR, you'll want item # S64027. This was designed in response to that Toyota hitch and has a 4-1/2" insertable span.

Is this what you're needing the hitch pin for?

expert reply by: Jerred H

0

Locking Anti-Rattle, Threaded Hitch Pin
(click to enlarge)

Tony

8/19/2025

I already have that for the swagman. I’m looking for a pin to work with my older Allen bike rack on the Tacoma

Jerred H.

8/19/2025

@Tony The Swagman item # S64027 is the only one that's come out that's compatible with the threads on a bike rack and fits that wider 2" receiver. If you can get the threaded portion out of your Allen bike rack you can use our etrailer Hitch Pin Lock item # e98881 to mount and secure it.

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Will the Replacement Anti-Rattle Hitch Pin Work w/ a Toyota 2" Receiver?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching