Is There Latch Repair Kit for Bulldog 44150W Coupler

Question

Question:

Does someone make a latch repair kit for a bulldog 44150W a frame? Thanks!

asked by: John H

0

Expert Reply:

Hey John, actually yes we have the part # F670801 which is correct repair kit for the Bulldog 44150W.

expert reply by: Jameson C

0

Jameson C.

9/26/2025

Hey John, did the repair kit for the Bulldog 44150W work out for you? I’d love to hear your outcome because it could give others confidence when ordering replacements.

Answer 1

Good question, Tina - you’re in the safe zone with the M-3 aluminum plate #M348FR. It’s 3/16 inch thick and fully welded across the piano hinge (some cheaper ones are just bolted instead of welded), so even with heavy mowers or small tractors, it…

view full answer...

Answer 2

Hey Jim, an E5 error code on a Furrion RV Tankless Water Heater #FR93FR means that you have an Air Pressure issue. This means you could have the following issues: Exhaust Blockage: Remove any obstructions to the exhaust vent/clean off. High Winds…

view full answer...

Answer 3

I do have options for you but trailer coupler repair kits are not exactly universal. If I knew the exact trailer coupler you have on your trailer then I could confirm 100% whether or not we have a trailer coupler repair kit for you. However, it looks…

view full answer...

Answer 4

The Repair Kit Fulton Wedge-Latch Cast Head Coupler, #F670801, is designed to fit the coupler #BD44125W0317 which does take a 2-5/16 inch ball.

view full answer...

Answer 5

To charge the battery in the Engager Trailer BreakAway Kit, #20099, you can attach the wire from the 12 volt circuit on the trailer side 7-Way (1 oclock position on the back of the trailer side 7-Way where the wires attach) to the input wire on the…

view full answer...

Answer 6

A dead battery would not be the cause of your brakes not disengaging. A dead battery would have the complete opposite effect on your brakes. A dead battery wouldn't send the electric signal to engage the electric brakes and no electric signal…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Is There Latch Repair Kit for Bulldog 44150W Coupler

Continue Researching