Will Taller Equalizer Raise Height of Trailer
Updated 10/22/2025 | Published 03/26/2025 >
Products Featured in This Question
Question:
This equalizer is about two inches taller than the one currently on my tandum axle 5th wheel. I was considering flipping the axles to get more ground clearance. This kit would give me 1 inch taller suspension without flipping the axle. Are there any other considerations I should be aware of or options? Im trying to get a small amount of lift with flipping the axles, I think that would be too much. Are there springs with less arch ?
asked by: Mike
Expert Reply:
Hey Mike! Are you referring to the Dexter # K71-448-00? Adding a taller equalizer is possible but it won't raise the height of your overall trailer. You would also have to get longer hangers for the front and rear to match and raise the height. I don't recommend this since you may throw off your suspension if you don't get it right. The flip kit # K71-384-00 (2-3/8" axles) or # K71-385-00 (3" axles) is the most basic, cost effective way to do this.
You can also use the Correct Track # RR55QX to increase the height of all three sets of leaf spring hangers. This raises the height of the trailer by 1-1/4" or 2-1/4". Leaf springs with a flatter arch would not be effective so that isn't a solution. If you want to cut off your existing hangers and replace them all with longer ones that will work but it requires welding. It is important to make sure the increased length is the same for all three sets of hangers so you don't throw off your suspension geometry.
Product Page this Question was Asked From
Dexter Heavy-Duty Suspension Kit for Tandem-Axle Trailers - 1-3/4" Wide Double-Eye Springs
- Trailer Suspension Parts
- Suspension Kits
- Boat Trailer
- Snowmobile Trailer
- Double Eye Springs
- Tandem Axle
- Dexter
more information >
Continue Researching
- Search Results: axle flip kit
- Search Results: dexter spindle nut
- Search Results: castle nuts
- Search Results: trailer shelf
- Q&A: Full Axle vs Spindle Replacement for 2012 Forest River Stealth Toy Hauler
- Search Results: hitch
- Q&A: Will Longer Equalizer Cause Problems for Trailer Suspension
- Q&A: Recommended Replacement 3,500 lb Axle for an AL-KO Axle
- Video: Review of Dexter Trailer Bearings Races Seals Caps - Bearing Kit 3500LB Axle - DX76ER
- Article: How to Raise Your Travel Trailer Height
- Shop: etrailer Horizontal E Track - Black Powder Coated Steel - 2,000 lbs - 94" Long - Qty 4
- Shop: Lippert Manual Pull-Out Step for RVs - Single - 7" Drop - 24-1/4" Wide - Steel - 300 lbs
- Video: Review of Dexter Trailer Hubs and Drums - Pregreased Idler Hub - 8-259-5UC1-EZ
- Video: Trailer Axle w/ Electric Brakes Feature Review
- Shop: Trailer Axle w/ Electric Brakes - Easy Grease - 5 on 4-1/2 Bolt Pattern - 89" Long - 3,500 lbs
- Video: Review of Dexter Trailer Bearings Races Seals Caps - Bearing Kit 1-1/16 Inch BTR Spindle - DX59UR
- Video: Hands-On with the etrailer Hub Bearing Kit
- Video: An In-Depth Look at the Dexter Trailer Axle w/ Electric Brakes
- Video: Breaking Down the Curved Equalizer for 1-3/4" Wide Double-Eye Springs
- Shop: Aluminum Sendel Series S20 Machined Trailer Wheel - 16" x 6" Rim - 6 on 5-1/2
- Shop: Aluminum Sendel Series T17 Matte Black Mesh Trailer Wheel - 16" x 7" Rim - 8 on 6-1/2
- Shop: Maxtrax Xtreme Recovery Boards - Black - 9,900 lbs - Qty 2
- Article: Double-Eye Trailer Suspension System Review
- Shop: Suspension Kit for Tandem-Axle Trailers - 1-3/4" Wide Double Eye Springs - 2-1/4" Links
- Q&A: Can 3,500 lb Trailer Axle Springs be Replaced with 4,500 lb to Prevent Sagging
- Q&A: Replacement Leaf Springs and CRE3000 Equalizers for a 2012 Forest River Stealth Toy Hauler
- Q&A: What is the Best Grease for Trailer Bearings
- Shop: Vehicle Tow Bar Wiring
- Q&A: What Would be Trailer Suspension Height Difference Between Equalizers K71-359-00 and K71-448-00
- Search Results: 25~1/4 inch long trailer leaf springs



Robin H.
10/22/2025
Hey Mike, what did you end up doing to get the extra ground clearance on your 5th wheel? It’d be great to hear if the flip kit or the Correct Track lift gave you the height you needed. Your update could make it easier for others looking for a small lift without flipping their axles too much.