Replacement Brake Caliper Brake Pads for DBC-2250

Question

Question:

Do you have a cross reference pad to dbc-2250 caliper?

asked by: Edgar A

0

Expert Reply:

Hey Edgar, based on that part number the correct replacement brake pads would be the part # K2250CP which is Kodiak Ceramic pads for 8k to 14k axles.

expert reply by: Jameson C

0

Jameson C.

11/3/2025

Hey Edgar, did the Kodiak ceramic pads end up being the right match for your DBC-2250 caliper? Knowing how they fit could help others looking for the same replacement.

Answer 1

I attached a chart that has the automotive cross reference for the Kodiak disc brake pads part #K2250CP that you referenced under the yellow heading. Probably the easiest to look up would be 1982 to 1992 Chevy Cavalier.

view full answer...

Answer 2

Yes, the Kodiak Ceramic Brake Pads #K2250CP are the best brake pads we carry for the Kodiak Disc Brake Caliper 2250. The ceramic brake pads provide better performance and will make less dust while providing a longer life than the organic and…

view full answer...

Answer 3

The "KTC 7600" stamped on the brake pad doesn't look to be a part number, so I can't cross reference it, but we do know you have Kodiak ceramic brake pads. So to determine the correct brake pads, all you need to do is match up…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Replacement Brake Caliper Brake Pads for DBC-2250

Product Page this Question was Asked From

Continue Researching