What is the Diameter of the Base or Shank of the Gooseneck Trailer Ball # 19309

Question

Question:

What size shank does the 2 5/16 ball #19309 have. I am looking for a 2 5/16 ball with a 2 5/16 shank, i am having trouble finding this ball. Please let me kow if you have one like this or where i can find one. Thanks

asked by: jessie

0

Expert Reply:

The diameter of the base, or shank, of the Hide-A-Goose Gooseneck Hitch Ball, item # 19309, is 2.6 inches, or just under 2-5/8 inches. At this time we do not have a Gooseneck ball with a 2-5/16 inch, base or shank.

expert reply by: Robert G

0

Answer 1

The CURT Trailer Hitch Receiver #C15445 that you referenced should work well for your 2000 Ford F-350 with a single rear wheel axle as this hitch is confirmed to fit all models of the 2000 Ford F350 cab and chassis. As long as the fuel tank is in the…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The etrailer.com Electric Trailer Brake Kit #AKEBRK-7-SA and the Dexter Nev-R-Adjust Electric Brake Kit # 23-464-465 referenced in your question are both self-adjusting assemblies that will work to replace the existing Dexter brakes on your 7,000…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

I currently have four different self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes. You can choose from the following: -Terran Axle Electric Trailer Brakes #TX97ZJ (3,500 Axles) -etrailer Electric Trailer…

view full answer...

What is the Diameter of the Base or Shank of the Gooseneck Trailer Ball # 19309

Continue Researching