Can Bolt On Trailer Coupler be Welded On

Question

Question:

Can you weld on coupler in place of bullying it on

asked by: Kenneth P

0

Expert Reply:

Hey Kenneth, yes basically all couplers that were designed to be bolted on can be welded on.

expert reply by: Jameson C

0

Jameson C.

12/15/2025

Hey Kenneth, how did it go welding the coupler instead of bolting it on? Your update could make it easier for the next person deciding between the two methods.

Reply

Kenneth P.

12/15/2025

Worked wonderfully

Reply

Jameson C.

12/15/2025

@KennethP Nice!!

Reply

Answer 1

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 4

There is no exact way to determine the leaf spring length. The best way to determine the length for a replacement is by measuring the existing leaf springs. The hanger distance and shackle length can help you get a good idea, but you're looking…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hello Graham, thanks for reaching out. Both the parts you mentioned, the Timbren #T54KV and #TASR5200S03 are 5,200 lb axle-less systems. The difference is the #T54KV is designed for off-road applications with offroad tires while the #TASR5200S03 is…

view full answer...

Answer 7

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 8

The determine the correct replacement leaf spring on your 2021 Coachmen 259FKDS you'll need to lift your trailer frame so the spring is hanging freely and then measure from center-eye to center-eye, then for the equalizer you need to measure…

view full answer...

Answer 9

Hey Rusty! Can you measure the flat length? Check out the help article below which explains how to measure. This is the best solution for worn out leaf springs. Realistically they're probably a little shorter than 24-7/8" which means we…

view full answer...

Answer 10

Hey JT! Sorry to hear about your trouble with the leaf springs. Hopefully there wasn't a lot of damage and everyone stayed safe. From what I have found the 26E-3500 is the same as the Dexter 072-027-00. This is the 6-Leaf Double-Eye Spring for…

view full answer...

Answer 11

Hi Austin, I can help you determine the right replacement double-eye leaf springs for your 2018 Jayco trailer, though we don't have any way of knowing what specific ones you need. It's pretty easy though, as all you need to do is measure your…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Can Bolt On Trailer Coupler be Welded On

Product Page this Question was Asked From

Continue Researching