What Axle Is Compatible WIth The 5 on 5-1/2" Hubs AKIHUB-555-35-EZ-K?
Updated 12/15/2025 | Published 11/01/2024
Products Featured in This Question
Question:
Good morning, I currently have a 6x10 utility trailer that the wheel bearings went out on. But one side the nut wiped out the threads and the axle is also bent so im thinking its time for an axle. So Ive been searching google and multiple sites. My current hub is 5x5.5. and no complete axle ive found comes with that hub. And I dont want to spend the money on a whole kit with new wheels and tires. Ive found on your site you have hubs 5x5.5, part number AKIHUB-555-35-EZ-K im curious if you could lead me to the correct axle that those hubs would fit so i could potentially just get a new axle and hubs. or do you have axle with the hubs i need. just a 3500lbs non brake axle. thank you!
asked by: Jason K
Expert Reply:
Hello Jason, thanks for reaching out. The 5 on 5-1/2" hubs are pretty uncommon these days, so I am not surprised to hear that there are no complete axles that come with them.
The Easy Grease Trailer Idler Hub Assembly # AKIHUB-555-35-EZ-K you mentioned will fit any standard 3,500 lb axle. The hub uses the # L68149 (1.378" inner diameter) inner bearing and # L44649 (1.063" inner diameter) outer bearing which is standard for the 3,500 lb axles.
We offer a few compatible axles, like the # e53GR which is 89" long and the # e38GR which is 89" long. Both axles are compatible with the # AKIHUB-555-35-EZ-K hubs, it just depends what length of axle you need.
Feel free to reach out if there is anything else I can do to help.
Product Page this Question was Asked From
Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 5-1/2 - Pre-Greased
- Trailer Hubs and Drums
- Idler Hub
- EZ Lube
- Pre-Greased
- L68149 / L44649
- Standard Grade
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 5-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- etrailer
more information >
Continue Researching
- Q&A: Does The Gen-Y Adjustable 2-Ball Mount w/ Stacked Receivers 325-GH-513 Come With The Pintle Lock?
- Q&A: Need Replacement For UFP PG1090 Actuator On Magic Tilt Single Axle Trailer
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Q&A: What is a #84 Spindle and How Do I Know I Have One On My Trailer?
- Q&A: 5-Lug Trailer Hubs With Inner Bearing L68149 & Outer Bearing L44649 for Boat Trailer
- Q&A: Looking For Hub With 68149 Inner And 67048 Outer Bearings
- Q&A: Upgrade to Replace Fulton Boat Trailer Jack FTJ120W0301
- Q&A: Installation of Emergency Break Away Cable Repair Kit for Dexter Axle A-60 Brake Actuators
- Article: Trailer Tire Sizing
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Adjust Your Trailer Brakes | The Ultimate Guide
- Article: Brake Controller Installation: Starting from Scratch
- Article: Trailer Wiring Diagrams
- Article: How to Change the Axle on your Boat Trailer Without Leaving your Driveway
Jesse M.
12/15/2025
Hey Jason, how did things go with the new axle and the 5 on 5-1/2 hubs for your trailer? Were you able to get everything matched up with one of the 3,500 lb axles? Your update could make it easier for others trying to keep their same wheel setup.